24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Customer Questions and Answers for Control Board Kit by Whirlpool

  1. Our Price $119.44
    Compare At $142.13
    You Save $22.69
     
    • Part Number: AP4009643
    • MFG Part Number: 12002713
    • Made by: Whirlpool
    Add to Cart

Questions & Answers

For Whirlpool Control Board Kit (Part Number: AP4009643)

Answer or Comment

View all Questions

What about not being able to change selection on panel? When we try to change from one wash selection to another (or anything else) it will not change.

Angie for Model Number PDBL390AWW

ANSWER Hello Angie, I would first check the connection at the ribbon cable. If you take a pencil with an eraser and go in the same direction as the leads on the ribbon cable, this cleans the connections better than anything elst I've found. If you still get no results, you may have to replace the control 12002713. The panel contains the membrane switch 6-919816. I want to tell you to put it into the self diagnostic program, but if it's not responding for the wash cycles, it probably will not respond for the self-diagnostics. To initiate the diagnostics test cycle, press the following sequence of keys within 10 seconds: High Temp Wash, Air Dry, High Temp Wash, Air Dry or Power Scour, Air Dry, Power Scour, Air Dry The diagnostics test cycle may be manually advanced to the next interval by pressing the pots & pans key. To exit diagnostics, press cancel. 2. The sales demo cycle consists of a single 6-minute wash interval which starts at interval 1 and concludes at interval 0. To initiate the sales demo cycle, press the following sequence of keys within 10 seconds: High Temp Wash, Air Dry, High Temp Wash, Air Dry, High Temp Wash or Power Scour, Air Dry, Power Scour, Air Dry, Power Scour 3. The diagnostics test cycle executes a soil sensing interval at interval 9 to test the soil sensing circuit. The sensing LED is illuminated throughout this sense interval. If the soil sensing pressure switch is tripped at any time during this sense interval, the control will immediately terminate the sense interval and proceed with the remainder of the diagnostics cycle. If the time limit for this sense interval elapses without detecting soil, the control simply proceeds with the remainder of the diagnostics cycle. 4. The diagnostics cycle suspends cycle timing and executes a thermal hold at interval 7. The thermal hold interval is terminated and cycle timing resumes when the water is heated to the desired set point temperature (60ºC/140ºF). The maximum default time limit elapses (1 hour), or the cycle is manually advanced to the next interval by pressing the pots & pans key. The water heating LED is illuminated during the thermal hold. 5. The clean LED is illuminated at the end of both the diagnostics test cycle and the sales demo cycle. The clean LED can be extinguished by opening the door or pressing any key. 6. During intervals 9 through 3 of the diagnostics cycle, the clean LED is illuminated whenever the control detects a resistance of greater than approximately 45 K-OHMS on the thermistor/ thermostat circuit. This feature is intended to help determine whether a thermostat or thermistor is installed. A thermostat with normally open contacts would trigger the clean LED (until the thermostat is tripped). Under normal operation, the resistance of the thermistor is always less than 45 K-OHMS and would not trigger the clean LED. 7. The wash and drain auxiliary windings are only “on” when the motor is being started. When the control has determined that the motor has been started satisfactorily, the auxiliary winding will be turned “off”. 8. Entering the key sequence high temp wash (or power scour), air dry, high temp wash (or power scour), air dry, after a cycle has started, will enable the pots-n-pans key rapid advance feature. This will allow service to rapidly step to any interval of the currently running cycle. Other Control Features: Cancel/Drain: Terminates current active cycle and clears cycle selections. Executes 2-minute drain upon first selection if water is likely to be left in sump. Subsequent selections toggle between 2-minute drains and going to standby. Control Lock: The control lock LED is illuminated and all keys of the keyboard are disabled whenever the control lock feature is invoked by the customer. The control lock feature (and LED) can be turned on or off by the customer at any time by holding down the air dry option key for 4 seconds. Error Messages: Stuck Key: If the control detects that a key is stuck in the depressed position, dishwasher operation will be suspended and the control will flash the LED associated with that key until the condition is corrected. If a key without an LED is stuck or multiple keys are stuck, the control will flash the lock-out LED. If we can assist further please let us know. 

Answered by AppliancePartsPros.com   |   Thursday, April 12, 2012

We are Safe, Secure, Dependable and Trusted
  • BizRate.com Customer Certified Site - Click to Verify