24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Customer Questions and Answers for Pump, Water Circulation by Whirlpool

  1. Our Price $106.71
    Compare At $126.98
    You Save $20.27
     
    • Part Number: AP4411210
    • MFG Part Number: W10233462
    • Made by: Whirlpool
    Add to Cart

Questions & Answers

For Whirlpool Pump, Water Circulation (Part Number: AP4411210)

Answer or Comment

View all Questions

My Maytag Bravos had been making loud noises while it was draining during the spin cycle, now it is showing an error code of F50 and wont do anything. Is this a pump issue?

Diana for Model Number Mtw6600tb0

ANSWER Hello Diana. F then 50 flashes when the motor rotor position sensor (RPS) senses no rotation. ? Does basket turn freely? If not, make sure bottom shipping pack has been removed. Determine cause of friction. This test checks the wiring to the motor and rotor position sensor; and the motor and rotor position sensor themselves. NOTE: Drain water from tub. 1. See Activation of Manual Diagnostic Test Mode, page 3 and check the motor and electrical connections by performing the Spin test under Manual: Motor, page 2. The following steps assumes that this step failed. 2. Unplug washer or disconnect power. 3. Check to see if basket will turn freely. ? If basket turns freely, go to step 4. ? If basket does not turn freely, determine what is causing the mechanical friction or lock up. 4. Remove the console to access the machine/motor control assembly. See Accessing & Removing the Electronic Assemblies, page 6. 5. Visually check that the P5 and P10 connectors are inserted all the way into the machine/motor control. ? If visual checks pass, go to step 6. ? If visual checks fail, reconnect P5 and P10 and repeat step 1. 6. Visually check that the P5 and P10 connectors are inserted all the way into the machine/motor control. ? With an ohmmeter, verify resistance values as shown below. P5 1-2 31 O ± 5 O Much higher than 31 O Resistances at all connectors are correct 1-3 P10 6-5 1.5 kO ± 100 O Much higher or much lower than 1.5 kO 6-4 6-3 1-7 600 O to 21.2 kO Out of range 7. Tilt machine forward to access the bottom of the machine and the drive motor area. See figure 1, page 5. Remove the motor bolt, then the motor cover to access the motor connections. See figure 2, page 5. 8. Visually check the mounting bracket and electrical connections to the motor and rotor position sensor board. ? If visual check passes, go to step 9, page 5. ? If visual check fails, reconnect the electrical connections, reassemble stator and motor cover and repeat step 1. 9. With an ohmmeter, check for continuity between all pins on the P10 machine motor control connector and the motor rotor position sensor (RPS) connector. See figure 2 at right and figure 4, page 16. ? If there is continuity, check the motor windings. If the motor windings are open, replace the drive motor. ? If there is no continuity, replace the lower machine harness. 10. With an ohmmeter, check for continuity between all pins on the P5 machine/motor control connector and the drive motor connector. ? If there is continuity, replace the drive motor. ? If there is no continuity, replace the lower machine harness. 11. The drive motor and lower harness are good. Replace the motor RPS board and perform the Diagnostics test in step 1 to verify repair. 12. If the Diagnostics motor test in step 1 failed, then the machine/motor control has failed: ? Unplug the washer or disconnect power. ? Replace the machine/motor control assembly. ? Perform the Motor Diagnostics in step 1 to verify repair. 

Answered by AppliancePartsPros.com   |   Thursday, March 07, 2013

We are Safe, Secure, Dependable and Trusted
  • BizRate.com Customer Certified Site - Click to Verify