Frigidaire 154576501 Bottom Door Seal - AppliancePartsPros.com

Total
$0.00

Part Number:	AP3959846
MFG Part Number:	154576501
Made by:	Frigidaire

Our Price
$11.71
Regularly	You Save
~~$13.93~~	$2.22

Most Interesting

A thin piece of rubber looking like a gasket came loose from the bottom of the door. It did not totally come off but is hanging. I am reluctant to remove it completely until I know what to buy to replace it . . . and have the part in hand. I also would like to know how to install the replacement part and what tools or adhesives will be needed.

Crd for Model Number FGBD2431KB1

Answer Hello CRD, The rubber gasket would be the bottom door seal 154576501. To remove and install you will need to remove the inner door panel. To remove inner panel, remove the screws on the inner panel and lift up.

Was this helpful?

How do you install a bottom door seal on a frigidare dishwasher and do you need a tool or adhesive to hold in place?

Frank

Answer Hello Frank. On the bottom of the inner door panel you will feel the seal. The old seal pulls out from the bottom of the panel. There is a lip inside the panel on the bottom. You slide the new seal 154576501 into the lip on the inner door panel. There is no adhesive needed for the repair.

Was this helpful?

A piece of rubber looking much like a seal tore off the bottom of the door of the dishwasher. The dishwasher now leaks onto the floor. The part looks like a seal of some sort. Is that the same thing as the Frigidaire 154576501 bottom gasket? I would like to purchase and replace the part on my own as the current owners are very elderly and unable fix it on their own. Is there any other part or supply I may need to fix the leak? Thank you so much!

Tia C for Model Number PLD2850RDC2

Answer Hello Tia, Yes the bottom door seal 154576501 would be the part that you would need if the unit is leaking and the seal is torn. Also check the spray arms to make sure that they are not clogged or cracked.

Was this helpful?

Latest Questions

I have replaced the tub gasket and added the splash shield kit AP4338941. I have the door cover off but still can not figure out how to remove the old bottom door seal. The new one has what looks like a track it should fit in. With the door cover off I can only see approx 2 inches on each side, it looks like its covered by plastic. Do I have to take the door completely off? Mine also leaks through the middle of that bottom door seal.

Paul for Model Number FDB1050REM1

Answer Hi Paul. Unless the seal 154576501 is adjusted properly, it will leak. It has to make contact with the tub on the bottom, but still allow enough room in the middle for the water to flow back into the tub. These can be very hard to adjust correctly, and may require several adjustments to get correct. I know it can get exasperating.Thank You.

Was this helpful?

Need to know how to install dish washer lower gasket part number 154576501 ?

Answer Hi Tr. You will open the door and remove the lower rack. Then you can clip this seal on the bottom/inside of the inner door. Part #154576501.Note: If you continue to get water splashing at the bottom corners of the inner door after replacing this seal it is suggested to replace splash shield kit 154701001. Thank You.

Was this helpful?

I had new floors installed and they started Buckling. When we pulled the dishwasher out of the cabinet it was in we found it was leaking from a cracked nut gasket and from the bottom of the door. I need help fixing these issues,It's caused a lot of damage. It sounds like this is a very bad design.

Maurya S. for Model Number FDBB2040FB0

Answer Hello Maurya. The seal 154576501 can only be put into the door one way. It has a notch cut into it which fits over a plastic lip that exists only on one side of the seal slot in the door. Bottom of door is made to leak water around this bottom door seal, that's why the middle of this seal is cut out, to allow the water back into the main dishwasher tub. But, common problem is it allows too high a velocity of flow to come through and to splash out within the front door cover and down onto the floor. This must be why they made the "splash guard" kit 154701001. Make sure the seal is touching the bottom of the tub assembly. To install the brass nut, you will remove the wire and the old nut from the heater and screw the nut nut onto the heater and reinstall the wire. Hope this helps.

Was this helpful?

Bottom Door Seal

Questions & Answers

Description

Appliance Compatibility Tool

Repair Help

Questions & Answers

Most Interesting

Latest Questions

Cross Reference and Model Information