24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Chat with a Pro

Motor Kit

Part Number: AP5272381
MFG Part Number: 154844101
Made by: Frigidaire
Our Price
$114.10
Regularly You Save
$136.92 $22.82

In Stock — Ships Today Guaranteed

Satisfaction Rating (2)

Questions & Answers

28 Questions & Answers



Genuine Frigidaire part. Frigidaire brands include Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and others. See all items in Dishwasher Pump.
Electrolux also makes various appliance models for Sears / Kenmore

Appliance Compatibility Tool

Check your model number or use our Cross Reference Tool to find out if this part will work with your appliance.

Where can I find my model number?

More Product Images

Repair Help


Cross Reference Information

Part Number 154844101 (AP5272381) replaces 154795001, 154719201, 154574601, 154483001, 154579701, 154700001, 1940267, AH3501022, EA3501022, PS3501022.

Do-It-Yourself Stories from Customers like You
Total Satisfaction Rating
(2)
View All Do-It-Yourself Stories Have questions? Ask our pros!
Bad bearing in motor on dishwasher. Very loud. Larry B. • Azle, TX • March 31, 2014

My Repair & Advice

Was this review helpful to you?  

Most Helpful Stories

1 People found this story helpful
Do-It-Yourself Rating
  • 1
  • 2
  • 3
  • 4
  • 5
Easy Difficult
Repair Time Estimate

15-30 minutes 

Thr motor pump group, the beraings in the motor were bad , causing the water pump not to work Basil F. • York, PA • March 13, 2014

My Repair & Advice

Was this review helpful to you?  

   
Do-It-Yourself Rating
  • 1
  • 2
  • 3
  • 4
  • 5
Easy Difficult
Repair Time Estimate

15-30 minutes 

Have a Repair Question?
AppliancePartsPros has your Answer!

Questions & Answers

Read all 28 Questions

Ask a Question

Most Interesting

My dishwasher has been running louder than normal and does not drain when the wash cycle is complete. I've removed and cleaned the the base, support and filter assembly and am still having the same issue. Do I need to replace the pump assembly (A00126401)?

Billy H for Model Number FGHD2433KF1

Answer

Was this helpful?

Frigidaire dishwasher started leaking and ruined my kitchen floor. Shut down and saw water coming from bottom of motor housing. I read the various suggestions and ordered both the front and rear o-ring on the motor. I carefully cleaned and installed the motor housing back into place. Turned on water and it still leaks the same if not more then before. I traced the leak to the (4-5 cut vents) between the actual motor and internal impeller. I can only assume at this point the shaft seal is bad and the entire assembly needs replaced? Can you shed some light as there is no breakdown of the motor assembly itself so any troubleshooting from this end is limited. What do you suggest to check at this point? JImmy D

Jimmy D for Model Number FGHD2433KF1

Answer

Was this helpful?

Does the replacement motor, AP5272381, come with the foam insulation for the motor housing and the inner and outer "O" rings.

David for Model Number PLD4375RFCO

Answer

Was this helpful?

Latest Questions

My dishwasher started making a squeaking noise a couple a days ago and has changed into a constant whirring type noise. I took the bottom panel off and it sounds like it's coming from the circulation pump. I also noticed that it is leaking. Is this the circulation pump or am I overlooking some other possibility? Do you think the noise and the leak are same problem? Thank You Jim

Jim for Model Number fdb2810ldc0

Answer

Was this helpful?

Dishwasher leaked persistently during wash cycles. Removed the motor, cleaned the two O rings and deposits around housings. Reduced the leaking, but not completely. Dishwasher now leaks slowly, one drop per second, at beginning of first cycle, no leaks detected during any of the cycles, then perhaps hours after the washer completes the last cycle the leaking reoccurs. No accurate volume measurement, but enough water to saturate several sections of paper towel. After some time the leaking stops, but there is always about 1" to 2" of standing water remaining in the basin; but water level is below the filters. Paper towels are used as a litmus test. I don't see cracks in either the motor housing or the basin mount where the motor slides into, but i am curious if the basin mount is two pieces or one. It seems that the problem could be temperature related: as the components heat up during operation they expand, and perhaps close gaps that later reopen when the temperature drops back down. I suppose that could effect the orings, but i don't think it explains the standing water. the drain cycle must work even a little, otherwise there would be way more water in the basin? Can you help? Thanks, gcb

Gcb for Model Number FDB4315LFC2

Answer

Was this helpful?

Water comes out of my lower spray arm, but not my middle or upper spray arms. I have cleaned them, they are not blocked. Dishes on upper rack are left with a residue after cleaning.

L Z for Model Number fdb2810 ldc1

Answer

Was this helpful?