Frigidaire 5303918277 Replacement Icemaker

Total
$0.00

Part Number:	AP3160597
MFG Part Number:	5303918277
Made by:	Frigidaire

Our Price
$79.95
Regularly	You Save
~~$148.58~~	$68.63

Most Interesting

I have ordered and replaced the control board. It did not solve the problem. As you can see above we have tested the microswitches for continuity and they were fine. I also double checked with the new control board in place by removing the microswitches and it did nothing. As soon as it's plugged in, the ice dispenser immediately kicks on and stays on. Any thoughts on what to check next? Thank you!

Sam for Model Number Fridigaire Gallery GLRS267ZAW4

Answer Hello Sam. There are two boards in your dispenser. Usually the one you changed fixes it, but since we are dealing with a shorted out componet here, it could be the other board. Here is the part number for the other board 241700109. Hope this helps.

1 person found this answer helpful.

Was this helpful?

After further investigation I realized what was being discussed. I apologize. I have checked both switches for water and ice dispensing with an ohm meter and both are good. Any other thoughts? Thanks

Sam for Model Number Frigidaire Gallery GLRS267ZAW4

Answer Hello Sam. If the switches are good, then you may need to replace the control board 5304422632. Hope this helps.

1 person found this answer helpful.

Was this helpful?

I am not sure where to find the micro-switch. Is it literally the switch/button you would push to dispense ice? If so, the one suggested looks different than mine, or I am not seeing this switch. Thanks

Sam for Model Number Frigidaire Gallery GLRS267ZAW4

Answer Hello Sam. Yes, according to your model number, these are the micro-switches for your dispenser. You will need to check your dispenser switches and see if they are making contact. It is ok if they are different, we just need to make sure they are not calling for dispensing. Hope this helps.

1 person found this answer helpful.

Was this helpful?

Latest Questions

A gasket like black material in pieces in coming through and frozen in the ice cubes.. Would it be a single part replacement or entire ice maker unit replacement. Ice maker works fine other than the black specks. What do you suggest? Thank you!

Richard for Model Number White Westinghouse RT 217 NCWO

Answer Hello Richard. Based on the information you provided, it sounds like the icemaker will need to be replaced on the unit.

Was this helpful?

I just hooked up the ice maker on a 8 year old fridgidaire that the ice maker had not been used for about a year. It will make ice very slowly. When the cubes are frozen it seems they lay on top of the ice maker for an extended time before ejecting. It only dumps ice about four times in 24 hrs. Also, what is the adjustment screw on the front for that has a neg. and pos. marking on it. The temp. is 0 deg. and the water line is not frozen. The ice maker worked fine when used previously. Thanks for your help. Steve

Steve

Answer Steve, If you have a filter in your unit, you will want to make sure that the filter is good. It may be that there is not enough water getting into the icemaker which would cause the icemaker to make smaller cubes and to cause it to take longer to make the cubes. If water checks ok then the thermostat on the icemaker would be the problem which would require a new icemaker. The adjustment screw if for more or less water.

Was this helpful?

I have received the part removed the old one and inserted the new one, it would not work, seemed like water was not going thru.? the Original problem was when the ice was ready to dump into box it would dump two cubes I would have to manually remove them in order for the ice maker to continue to work. So I thought I'll try to replace the ice maker to see of the works. I know the part is correct but maybe there is some adjustment that need to be done in order for it to work? or is the ice maker defective?

Katina X for Model Number FRS26ZSHB2

Answer Katina, The first thing that you always want to make sure of is that the water filter is good on the unit. The next thing that you want to check is to make sure that the fill tube is not frozen. If the fill tube is frozen then it will need to be cleared and you would want to replace the water valve due to seeping, which means a little water is trickling through the valve and flash freezing in the tube.

Was this helpful?

Replacement Icemaker

Questions & Answers

Description

Appliance Compatibility Tool

Repair Help

Questions & Answers

Most Interesting

Latest Questions

Cross Reference and Model Information