Frigidaire 131845801 Sensor-Moisture, Assembly W/harness

Total
$0.00

Part Number:	AP2107715
MFG Part Number:	131845801
Made by:	Frigidaire

Our Price
$89.86
Regularly	You Save
~~$106.03~~	$16.17

Most Interesting

I bought this item and it arrived without screws. I found one screw that would sort-of hold it in but most screws do not grab, the threads are too shallow. Shouldn't it have arrived with screws?! For the price paid I feel like the hardware should have been included. Could you tell me what kind of screw I need; something I can buy at Home Depot? Thank you.

Bradley

Answer Bradley, the screw that holds in the moisture sensor assy w/ harness 131845801 is a 10-16 X .50 screw. The part number is 131302800. Thanks.

Was this helpful?

dryer starts then stops with code eo68. took off control panel and cleand the buttons put back on to make sure thy were not sticking. still have code need help.

Junior for Model Number eaq6000eso frigidaire

Answer Junior, The E68 error code indicates that there is current leakage to ground on heater or the fuse is open. You will want to check the resistance of the heating element which should be approximately 14 ohms. Check the resistance between the ground and both the heater terminals. It should open when heater terminals are disconnected. If the readings are incorrect then replace the heating element. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Was this helpful?

Is there a lint filter cover that will work with the kenmore 417.83142300 that does not have the sensor? We don't use the auto dry cycle. The cover is physically broken is the reason for replacement. Looking around on the internet I found some that look like it and they were much cheaper I'm assuming because they don't have the sensor but don't want to buy something that won't fit.

Nick for Model Number 417.83142300 kenmore

Answer Nick, the same lint cover without the sensor is part number 131622202. Thanks!

Was this helpful?

Latest Questions

I just asked a question about how the female moisture sensor wire ends connect to the male connectors. Am I understanding right that as long as one wire is connected to the top sensor and the other wire is connected to the bottom sensor, it doesn't matter if they are connected on the same side (top/bottom) or on opposite sides (top to bottom). X----- X OR X------ X OR X X------ Y------ Y Y Y------ Y------ Y THANK. Hopefully, I not confusing you. The above X's and Y's represent the male tongue connectors on the lint filter housing (and connected to the metal sensors on the other side)and the dotted lines the female connector wires coming from inside the dryer body.

Al S for Model Number AEQ6000ESO

Answer Al, Your understanding is correct, The moisture sensor circuit is not a polarity sensitive circuit. As long as the two wires are attached to the terminals on the same end of the sensor bar(s) and attached to the wire harness connector properly, you'll be fine. Thanks and Good Luck

Was this helpful?

I cleaned my filter trap and took off the sensor moisture assembly by removing two screws. I disconnected the two wires which hooked up to the moisture sensor assembly and I forgot which spade, top or bottom, the wire with a white stripe hooks up to. I know which side they hook up to but is the wire with the white stripe on the top or bottom spade connector as you look at the enclosed diagram of part ap2107715: http://www.appliancepartspros.com/Appliance-Parts/frigidaire-sensor---moisture--assembly-w-harness-item-number-ap2107715.aspx Thanks.

Al S. for Model Number AEQ6000ESO

Answer Hello Al, The sensors are reading resistance from one to the other. It doesn't matter if you hook the wires up to the opposite one or not. It will still read the resistance from one to the other.

Was this helpful?

What does this sensor do and what are the symptoms if it goes bad?

David for Model Number 417.49012890

Answer Hello David. If the sensor 131845801 goes bad, the unit does not work int he auto dry cycles. It can not sense the moisture in the clothes. Hope this helps.

Was this helpful?

Sensor-Moisture, Assembly W/harness

Questions & Answers

Appliance Compatibility Tool

Repair Help

Questions & Answers

Most Interesting

Latest Questions

Cross Reference and Model Information