Frigidaire 318004900 Switch, Thermal - AppliancePartsPros.com

Total
$0.00

Part Number:	AP2126993
MFG Part Number:	318004900
Made by:	Frigidaire

Our Price
$88.72
Regularly	You Save
~~$104.69~~	$15.97

Most Interesting

Hello,where is the thermal fuse located and how do I get to it.

Bob for Model Number pleb30s9dca

Answer Bob, The thermal fuses are located on the back of the unit. You will need to pull unit out and disconnect power. Remove the lower back panel and there will be 3 thermal fuses. You will want to check all of them for continuity. If no continuity then they are bad or push the red button to see if they have tripped.

Was this helpful?

I replaced the bottom element on the top oven (baking element) it still doesn't work the bottom oven works good and the top element on the top oven works. What else can I look for?

Roger W. for Model Number pleb30t8ccb

Answer Hello Roger. Based on the information you provided, you will need to replace the relay board 318022002.

Was this helpful?

I have a Kenmore double wall oven that is not heating properly. At first, it was just the top oven. When you would set the oven to a specific temperature, the oven would beep telling you it was heated to the right temperature. In actuality, the oven was not ready and would not reach the right temperature. We switched to using the bottom oven only, which at the time seemed to be working fine. But now after several weeks the bottom oven is behaving the exact same way. So now both ovens beep stating they are at the "correct" temperature and ready to bake, when in actuality neither of them are heating to or maintaining a correct temperature. Do I have a switch issue, a thermostat issue, or a control board issue?

Brendan for Model Number Kenmore 790.47773405

Answer Hello Brendan. Test and make sure the voltage coming to the unit is correct. Make sure the oven sensors read around 1100 ohms at room temp. If all is good, you will need to order and replaced the control board in the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Was this helpful?

Latest Questions

Thanks for the response. However I read the multimeter instructions. I'm still not sure how to test the control board to see if I'm getting 120 volts to the bake terminal. Could you help with that. And if i'm not getting the voltage and need to change the control panel out which part number is that? I see two options 318010700 or 318192812.

Chris for Model Number pleb30s8ccc

Answer Hello Chris, To check the unit you will need to access the clock assembly. When you have the clock assembly accessed you will check from L2 out to Bake or terminals P8 to P3. You should have 240vac between these terminals. If you do not have 240 vac then you will need to replace the clock assembly 318010700.

Was this helpful?

My oven stopped working after a self clean. I have installed a new thermal switch with no change the unit will not heat. I then switched the broil and bake wires to each elements. when I hit bake nothing happens, when I hit broil the bake element will glow. So my question now is do I have a problem with those wires going to bake element? control panel? or something else?

Chris for Model Number pleb30s8ccc

Answer Hello Chris. Test the board and see if it sends out 120 volts on the bake relay. If not, replace the control board in the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Was this helpful?

My wall oven quit working after a self clean cycle. We changed the thermal switch. Still no heat. We switched wires from bake to broil as someone suggested. After when bake was selected nothing happened but when we hit broil the bake element started to glow. At this point could the problem be the control panel? thermostat? or something else?

Wendy for Model Number pleb30s8ccc

Answer Hello Wendy, If you replaced the thermal fuse and the bake is still not working then you would need to replace the control board 318010700.

Was this helpful?

Switch, Thermal

Questions & Answers

Appliance Compatibility Tool

Repair Help

Questions & Answers

Most Interesting

Latest Questions

Cross Reference and Model Information