GE WD15X93 Dishwasher Water Inlet Valve

Total
$0.00

Part Number:	AP2039339
MFG Part Number:	WD15X93
Made by:	GE

Our Price
$18.11
Regularly	You Save
~~$42.01~~	$23.90

Most Interesting

We have the GE Potscrubber 900, a very old (close to 20 years) dishwasher. We have leaking which looks like it's coming from the water valve which is blue. There's a very small hole spray water. Is part number AP2039339 the correct part for our model? Also, do you provide instructions on replacing the part?

Kevin for Model Number GSD900D

Answer Hello Kevin! Yes, WD15X93 is the correct water valve for the GE models GSD900D-*. The part does not come with instructions, however, we have a free repair forum you can visit for installation instructions. Here is the link to register and post a question, thanks! http://forum.appliancepartspros.com/register.php

1 person found this answer helpful.

Was this helpful?

G.M. We have this potscrubber 1200 that came with no catalog, so every thing I've done has been oriented via internet. The washer seems to start out right, meaning the pump winds for a few, water channels in the well deck, but then the volcano barely moves as well as the spray arms. Seems like there is not enough water pressure to have the arms moving = crappy wash! Also, is he arm at the top suppose to move and spray dishes? I checked continuity on motor and solenoid and were good, but none for water valve? Should there be one as well and is this the whole problem, as to why there is no movement or good wash??

Tod for Model Number gsd1200x66

Answer Tod, You're on track, water level and temperature is very important in a dishwasher. Allow the dishwasher to fill and wash for 5(five) minutes, unlatch the door and check the water level, there should be 1/2 to 3/4 inch of water coverring the lower portion of the flaot cover WD12X445, if not, theres not enough water in the tub to properly operate the wash arms and pump, and you'll need to replace the fill valve WD15X93. The fill valve is working, but you most likely have an internal restriction in the valve body causing a slow/low fill

Was this helpful?

We have a Kitchaid dishwaser (model # shown) and water isn't going thru machine. All seems to be working but no water going thru cycle. All lights are green and we can hear humming sound. The machine was purchased in 2009. Can you help?

Bob J for Model Number KUDC03FVSS2

Answer Hello Bob. If the motor is humming, and the unit is filled with water but does not spray, you will need to look for clogs in the impeller. If none is found, replace the motor assembly in the unit.

Was this helpful?

Latest Questions

This is a 24+ year old dishwasher...which is twice or three times the expected life of units today. Several days ago, the water inlet valve/solenoid failed as water continued to fill (and spill) even when it was off. Now I like long-lived things: I drive a 40 year old 4x4, cut wood with a 32 y.o. chainsaw and heat with a 3 decades old wood stove. I've got a 35 year old shop vac that still out-pulls anything else. Now I can fix just about anything and replacing the water valve doesn't seem too difficult (famous last words....) and the price is quite reasonable. But is it 'worth it' to fix something beyond its expected life? Cheers

Apg for Model Number Hotpoint HDA497K-01

Answer Hello APG. If everything else is in good working order, it is worth ordering the valve and replacing it on the unit. Only you can make the decision on the repair being worth the part replacement.

Was this helpful?

Is the operating voltage for GE Dishwasher Water Inlet Valve (Part Number: AP2039339)220V?

Allan R for Model Number AP2039339

Answer Hello Allan. No, the water valve WD15X93 is 120 volts AC. Thank you.

Was this helpful?

I purchased the heater nuts and replaced them when they arrived this week, item number AP3965251, for my Electrolux model no. FDB710LCB0 following your recommendation, it still leaks. I did notice mineral deposits on the top of the solenoid. I’m convinced that this is the problem. While the dishwasher is in operation, there’s a steady stream of water from that location. When the dishwasher is off, I’ve observed water leaking in that area. Everything else remains dry and operating correctly. I’ll purchase the electric water valve solenoid and replace the existing unit. What additional part(s) would you recommend that I replace?

Gregg for Model Number Electrolux model no. FDB710LCB0

Answer Hello Gregg. If the valve WD15X93 is leaking on the unit, then that should be the only part you need. Just make sure the hoses are not leaking and causing the issue with the water leak.

Was this helpful?

Dishwasher Water Inlet Valve

Questions & Answers

Description

Appliance Compatibility Tool

Repair Help

Questions & Answers

Most Interesting

Latest Questions

Cross Reference and Model Information