GE WD21X10229 Module Control Asm - AppliancePartsPros.com

Total
$0.00

Part Number:	AP3883875
MFG Part Number:	WD21X10229
Made by:	GE

Our Price
$114.02
Regularly	You Save
~~$162.85~~	$48.83

Most Interesting

Hi. My dishwasher is doing this: Select Anti-bacterial cleaning with Added Heat, then start the unit. After it finishes filling the tub, the unit shuts off and switches the options to the following: Normal Wash, Heat Dry. Then, when you reset the wash options back to Antibacterial; Added heat it runs fine. Could this be a problem with the Module Control?

Steve for Model Number PDW9280L00SS

Answer Steve, You will want to run the unit through a diagnostic mode. On the back side of the toe panel should be the wiring diagram. This will have the service mode in it. If everything checks fine in the service mode then the control board is what would be at fault and need to be replaced.

Was this helpful?

THE DISHWASHER ONLY DRAINS SOMETIMES.NO CLOGS ,IMPELLER SPINS FREELY,DO YOU THINK THE DRAIN PUMP WORKS INTERMITTINGLY OR SHOULD I BE LOOKING MAYBE ELECTRICAL. I DONT WANT TO START BUYING PARTS I DONT NEED.MACHINE IS 7 YRS OLD.

Chuck for Model Number PDW8400J10CC

Answer Chuck, you're on the right track. It is more likely to have an intermittent or failed drain pump WD26X10039 than a defective control board WD21X10241 or wiring at this stage. You do want to make sure the filter screens and sump chamber are clear of any sediment, chemical build up or debris. You also may want to disconnect the drain hose from the plumbing, and drain the dishwasher into a bucket, a few times, this would clear any debris from the drain hose.

Was this helpful?

When starting the dishwasher, "Normal Cycle" and "Added Heat" are chosen, the "Start" button is pressed, and the door is shut. This worked consistently until the last few weeks, but now only works intermittently. Lately, when this procedure is followed, the dishwasher fills as usual, then empties immediately; all lights go off except green "Start" light, and then the dishwasher, on its own, turns off "Added Heat," switches to "Heated Dry," and then starts this new cycle, not the originally selected cycle. The dishwasher is then turned off, and then there is another attempt by me to set the correct cycle, and the same thing happens. This may occur 5-6 times before it will run the cycle selected. My wife tries switching to different cycles, pushing the up and down arrows, and eventually she is able to get it to stay on "Added Heat." and not switch to "Heated Dry." Does this sound like a Control Board issue?

Charles for Model Number GE Dishwasher PDW9980L00SS

Answer Hello Charles, This is usually caused by stuck a button on the control panel WD34X11158.

Was this helpful?

Latest Questions

I have a problem similar to Brad's with the pdw8880l00ss. Mine will start (begin to fill), sometimes start the cycle, sometimes just stop during filling and at other times, finish the rinse cycle and start the wash cycle andthen just stop. I've noticed that the cycle time under the same conditions as a few weeks ago is now 20 minutes shorter? Any ideas?

Geoff for Model Number PDW9980L00SS

Answer Hi. It seems like you have a couple different issue. Remove the lower kick plate. Inspect the float stem as it engages the float switch for positive engagement actions up and down (ON/OFF). Make sure the float stem has not fallen off the side of the lever and the side cover has not uncapped open allowing all of this. Once this is established, then the Diagnostic chart needs to be located (either behind the toe kick panel in with the electronic control board). Put the unit into a diagnostic mode. It sounds like the Turbidity Sensor test in the diagnostic needs tested. The Sensor is part # WD21X10202. Make sure the door latch/switches are staying closed. Let us know what the diagnostic error codes are so we can help. Thank You.

Was this helpful?

After starting the dishwasher it runs a few minutes (the first cycle). Clicks as if to switch to the next cycle but shuts off. This will happen repeatedly 5-6 times and then it will run once. It makes it past that first interval it will complete the rest of the cycles ?

Brad for Model Number pdw8880l00ss

Answer Hi Brad. WASHABILITY COMPLAINTS- Hot Water – Ample supply of water at 120°F minimum temperature is necessary. Do not use dishwasher soon after using clothes washer or filling bathtub. Remove the lower kick panel and find the tech. sheet. It will allow you to use the diagnostic mode and find the default code . This allows you to use the volt/ohm meter part # TJMA-DM1 to assist you in your diagnostics. Then you will check the complete circuit , wiring , connections, and devices with the wiring diagram at your hand. Thank You.

Was this helpful?

Why does my dishwasher keep running? Is it the control board?

BOB11 for Model Number PDW9280L00SS

Answer Hello Bob! It is possible that it could be a bad board. Is there anything showing on the control display? Does this happen on every cycle selected? Thanks.

Was this helpful?

Module Control Asm

Questions & Answers

Appliance Compatibility Tool

Repair Help

Questions & Answers

Most Interesting

Latest Questions

Cross Reference and Model Information