GE WB24X10115 Switch Membrane Blk - AppliancePartsPros.com

Total
$0.00

Part Number:	AP3203483
MFG Part Number:	WB24X10115
Made by:	GE

Our Price
$74.69
Regularly	You Save
~~$109.27~~	$34.58

Most Interesting

We have a 36 inch GE Model ZVB36SH1SS. When lowering the unit it got stuck on a box. I removed the box and the vent slammed down and now the motor just keeps running like it is trying to lower it. The fan isn't blowing but you have to unplug the unit to keep the motor from running. The unit won't budge when trying to lift it up as it seems jammed. Any suggestions? Thanks, KB

Kb for Model Number ZVB36SH1SS

Answer Hello KB. It sounds like the switches are not contacting and the ram is broken. This will need to be disassembled to determine which part is broken in the unit. Also, test the switches on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Was this helpful?

My GE telescoping downdraft is stuck in the UP position. The fan still works. I'm not really sure where to start. Any suggestions?

Dean L. for Model Number Jvb37h1bb

Answer Hello Dean, You will either have a bad start switch, a bad limit switch, a bad relay board or a bad motor. If you have a test meter, you can test these components. The tech sheet should be in an envelope or a sticker on the blower housing under the cabinet. This will guide you through the circuits. If you hear the unit trying to operate, you probably have a bad pivot arm.

Was this helpful?

My downdraft fan will not raise or lower. Assuming it is the switch. How can I check this? If the touch pad...do you have instructions to install?

Blake for Model Number WB24X10115

Answer Hello Blake, To properly assist you we will need your model number to help you with this. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx

Was this helpful?

Latest Questions

I pryed off the decorative trim and unplugged the switch. The female end of the switch plug is down about 3 or 4 inches and the access way is only about an inch square. The female end is not fixed so it must be held in place while plugging in the male end of the new switch. It seems like a couple pairs of long needle nose pliers is the only way, but with only a square inch access area, it is crowded and not possible to see. Is there a trick to plugging in this new switch? Thanks, Mike

Mike for Model Number ge profile downdraft jvb37h1bb

Answer Hello Mike, It's been a while since I last serviced one of these, but if I remember correctly, the snorkel was in the down position. I removed the cook top and set it on the edge of the counter top to allow room to remove the gear motor panel and access was greatly simplified. This was quite a lot more work since it was a gas unit and I had to disconnect the gas line but, in the long run, it was much easier than trying to connect the two without being able to see or physically touch either connector.

Was this helpful?

We have a GE Profile down draft unit. We were having trouble with the fan speed switch, it sometimes would not work-no fan at all. Now, we can't raise the unit at all! I realize there are several switches that to consider, but which one? I would hate to buy all of them just to find out! Any help?

Fred for Model Number JVB94SH1SS

Answer Hello Fred, I would try try the variable speed switch WB24X10035 since you were having trouble with it anyway. We have a one year warranty and one year return policy so there is no risk for you. Hope this helps!

Was this helpful?

Our G.E. vent does not have the jumper box. Our switch that makes the vent move up and down is already installed on the unit and has a ribbon cable thar runs from the switch directly to the motor. The switch is shorting but the motor still runs and we need to cut the ribbon cable to install a new switch without replacing the entire switch and motor. Any advise? Only the 36 inch vent has the switch with the jumper box that you can remove and replace.

Holly

Answer Hi Holly. The jumper lead is part # AP3205966. Thank you. Read more: http://www.appliancepartspros.com/Appliance-Parts/ge-switch-membrane-blk-item-number-ap3203483.aspx#ixzz1afbhDI4M'>http://www.appliancepartspros.com/Appliance-Parts/ge-switch-membrane-blk-item-number-ap3203483.aspx#ixzz1afbhDI4M http://www.appliancepartspros.com

Was this helpful?

Switch Membrane Blk

Questions & Answers

Appliance Compatibility Tool

Repair Help

Questions & Answers

Most Interesting

Latest Questions

Cross Reference and Model Information