GE WE4M364 Timer - AppliancePartsPros.com

Total
$0.00

Part Number:	AP3994849
MFG Part Number:	WE4M364
Made by:	GE

Our Price
$43.00
Regularly	You Save
~~$60.20~~	$17.20

Most Interesting

The timer on our dryer seems "stripped" as in it just turns with no clicks or resistance all the way around the dial. I'm assuming this means the whole timer needs replaced. It doesn't seem to be the knob since the knob still stays on the dial. Does this seem correct?

Holidaynapril for Model Number gtdp301elows

Answer Hello holidaynapril. Pull the knod off the timer shaft and look and see if it is cracked or broken on the unit.

Was this helpful?

I recently replaced my dryer timer with part number WE4M364. After installing I noticed that the timer is about 90 degrees off of what the backsplash panel shows. After reading a previous post, I noticed that one suggestion is the timer is in backwards. I checked and to my knowledge that isn't the issue. I looked at the wiring diagram and it appears all the wires are I the right place. I double checked with GE and they assured that it is the correct replacement part. The knob insert is inside the knob. Is there a way to adjust the timer shaft? Or am I missing something simple? Thanks for your advice.

Kenny for Model Number DX4500EG6WW

Answer Kenny, There is no way to adjust the timer shaft. You will want to check the knob to make sure that it is not cracked or broken. There is a possibility that the knob could be cracked and the insert shifted which would cause the knob to sit improperly on the shaft.

Was this helpful?

I ordered a timer switch and the one that came in doesn't have a lug to hook the ground wire to do I have to have a lug on the timer or do I not have to hook up the ground wire

Jason for Model Number dhdsr46egoww

Answer Jason, You can attach the ground wire to any metal surface in the control panel.

Was this helpful?

Latest Questions

My dryer is working ok. Looked at list of parts, including the knob and timer assembly. The knob is ok; not broken. The problem is that the dryer does not turn off and on at right dial setting. It goes through the cycles but turns off with the dial in between settings instead of correct off position. Do I need a timer or is there something else wrong?

Joe for Model Number DBSR46E3G1WW

Answer Hello Joe, The knob could be installed backwards or in the wrong position on the timer shaft. It could also be the incorrect knob if it has ever been replaced before. I would suspect the knob WE1M654 first. The second thing I would suspect is the knob insert WE1X980, since without the insert, the knob will not fit on the timer shaft properly. DBSR463EG1WW

Was this helpful?

A man was here to fix my washer and then the dryer went. Well the timer will not move 20min 30min so on and the heat is so low. He told us that it is the timer it is like it is only working on 110 not 220. The back plate in side the dryer will get hot if on long time but it will not dry any thing. All vents are clean.

Lorene for Model Number dbsr463eg4ww

Answer Hello Lorene, The timer on unit is only going to work off 120 vac not 220. You can test the timer using a multi-meter. On Normal time cycle you should have 120vac between the following terminals: T to X (timer), B to C (Motor) and A to B (Heater). If you have 120 vac to the heater but not heating properly then you will want to check the thermostats, thermal fuse and the heater to make sure that they are good. With 120 vac to the timer motor which is 2 black wires coming off motor and motor is not advancing then you would need a new timer.

Was this helpful?

My dryer doesn't start. I ordered the start swith from you. I replaced it but still the machine doesn't work. Please let me know what could be the problem.

Sergio for Model Number DBXR463EG1WW

Answer Hello Sergio, I would check the door switchWE4M415. You want to use a multi meter across the terminals on the door switch. With the door switch pushed in, it should show the switch in a closed position. With the door switch not pushed in it should read open. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Was this helpful?

Timer

Questions & Answers

Appliance Compatibility Tool

Repair Help

Questions & Answers

Most Interesting

Latest Questions

Cross Reference and Model Information