24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Customer Questions and Answers for Adaptive Defrost Control Board by Frigidaire

  1. Our Price $96.63
    Compare At $114.99
    You Save $18.36
     Watch Video
    • Part Number: AP4909015
    • MFG Part Number: 5303918476
    • Made by: Frigidaire
    Add to Cart

Questions & Answers

For Frigidaire Adaptive Defrost Control Board (Part Number: AP4909015)

Ask a Question

Most Interesting  |  Latest Questions

I've replaced the defrost timer board and my fan still isn't coming on. What do I check next?

Will for Model Number frs26hf6bw0

Answer

Was this helpful?

1 Answer

Had ice on my fan and was chipping it off with a knife. ( I know I shouldn't be doing that but it is what it is). Don't ask me how but as I was doing this the knife jumped the 2 prongs at the fan motor and the fan instantly stopped. Would that have shorted the fan or the defrost control board? What is the correct voltage output for the fan? I checked the voltage coming from the plug and I only get around 28 volts.

Dan for Model Number glrs264zaw

Answer

Was this helpful?

1 Answer

I have a bad ADC I can see its burnt up. My fridge was manufactured in 2004, do I have the latest wire harness or would I have to use the new harness that comes with the replacement for 241508001?

Dave for Model Number Kenmore side by side by fridgidaire

Answer

Was this helpful?

1 Answer

Thank you for any help in advance. My evaporator coils were not defrosting. I changed the old ADC 241 508 001 with a new ADC 530 391 8476 (Orange). My refrigerator has a single switch damper, so I did NOT change the wiring harness as stated in the instructions. This corrected the defrost problem, but now the refrigerator freezes over even on the warmest setting and turning the control knob will not affect the damper. I ran a test by putting the original ADC back in and turned the control knob and I could hear the damper open and close. I put the new orange one back in and the knob does not affect the damper with it in. I considered putting the new harness on, but it has extra wires on it so I did NOT switch it. The parts store switched out the new ADC with another and same problem. They do not have a solution. I called Electrolux and they do not have a solution. Does anyone know what the fix is? Thank you. Bud

Bud for Model Number FRS 6 LR 5 E M 6

Answer

Was this helpful?

1 Answer

Damper motor opens and closes continuously running after replacing AP4909015 (5303918476) Adaptive defrost control board. Can you help me with my issue.

Millard G for Model Number frs26lf8cw1

Answer

Was this helpful?

1 Answer

MY FREEZER WORKS WELL, BUT THE FRIDG. IS WARM, THE MODULE IN THE UPPER LEFT CORNER HAS ICE ON IT, THE SERIAL # IS SL31445789 MFG, DATE READS 2001 . 08 PS MY KIDS ALWAYS HOLD THE FRIDG. DOOR OPEN LOOKING FOR FOOD TO GROW

Don Fellion for Model Number 105.5260211

Answer

Was this helpful?

1 Answer

I installed ADC kit 5303918476 and now both freezer & Refrigerator run at 45 degrees. The replacement harness had one extra connection ? and only 1 connector where 2 had been connected on the damper. I had to guess which one to connect. I had previously replaced the defrost thermostat. Please help. Bill

Bill for Model Number FRS26KF5CQ0

Answer

Was this helpful?

1 Answer

It seem like the unit is always in the defrost mode the center dividing the doors is warm to the touch. Could this be a bad defrost control board or something else?

Tim for Model Number FRS23R4AW8

Answer

Was this helpful?

1 Answer

It seem like the defrost mode is always on could it be the control board or something else?

Tim for Model Number FRS23R4AW8

Answer

Was this helpful?

1 Answer

My refrigerator was not cooling past 45 degrees and the evaporator was all frozen up. I replaced the defrost thermostat. I then noticed the fan was turning on and off but would never run constantly and the temperature was still not getting above 45 degrees. I then replaced the ADV (Adaptive Defrost Control Board) part number 5303918214. I did so per the instructions and use the supplied wiring kit and removed one of the connections to the damper switch (EPS as indicated in the instructions). This is the ADC IV, in doing this I have been forced to remove what appears to be a temperature sensor that goes through the refrigerator side to the freezer side. After putting everything back together I plugged it back in and the compressor turns on and the Evaporator fan turns on, but the damper switch instantly closes and even when I adjust the temperature control it will not reopen the damper switch. Any suggestions on what to do next?

Dave for Model Number FRS26LF7DSO

Answer

Was this helpful?

1 Answer

 

 
 
We are Safe, Secure, Dependable and Trusted
  • BizRate.com Customer Certified Site - Click to Verify