Questions and Answers for Frigidaire 131605901 Agitator

Total
$0.00

Our Price	$60.82
Compare At	~~$71.77~~
You Save	$10.95

Will part no. 1316058 interchange with part no.131605901 for a Frigidaire washer ? My measurements are at the base, 14 in. X approx. 17 high. My washer is Frigidaire gallery 13 cycle hd commercial.

Wm B

Answer WM B., To properly assist you we will need your model number to help you with this. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx

Was this helpful?

Yes

1 Answer

I remove the top but don't know how to remove part under the top.

Rozina for Model Number 13160505901

Answer Hello Rozina. Once the cap is removed, you will need to remove the bolt in the center to remove the agitator from the unit.

Was this helpful?

Yes

1 Answer

Trying to remove/ replace a Agitator. Is there a video for this?

John Doe for Model Number GLWS1339ESO

Answer Hello John Doe. Remove the cap by pulling it off and then the dust cover under it. Next, remove the screw and lift out the agitator.

Was this helpful?

Yes

1 Answer

The four fins at the bottom of the agitator are almost completely gone. (There is only one left). Is there a illustration that could take me through how to remove the agitator?

John Doe for Model Number GLWS1339ESO

Answer Hello John. Pull off the cap number 66 in diagram and then pull off dust cover number 67. Then remove the bolt and washer numbers 56 and 57 and lift out the agitator. Here is a link to the diagram. http://www.appliancepartspros.com/motor-tub-parts-for-frigidaire-glws1339es0.html

Was this helpful?

Yes

1 Answer

My washer wobbles bad when it spins dry. my old one had straps to prevent that this one doesnt. What esle would it be?

Gabe for Model Number FE2831AS1

Answer Hello Gabe, The model number listed is not showing as a good model number. We will need you to verify the model in order for us to assist you better. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx

Was this helpful?

Yes

1 Answer

My washer will not agitate but it will spin out & drain. The top part of the agitator will spin freely both ways by hand. I've checked it without any clothes in it & the problem still exists. Would this mean it needs a new agitator?

Missy for Model Number GLWS1439FS1

Answer Hello Missy. Yes, based on the information you provided, it sounds like the agitator 131605901 needs to be replaced.

Was this helpful?

Yes

1 Answer

I'm attempting to take apart the agitator on my washer to check if the dogs need to be replaced (fairly certain that is the problem). However, no matter how hard I pull the upper agitator is not separating from the lower one. Will I need to replace the entire agitator with this model?

Mleckson for Model Number FWS1233FS0

Answer Hello Mleckson. Sorry, but there is no dogs used in this model. You will need to replace the agitator 131605901 in the unit.

Was this helpful?

Yes

1 Answer

How would I be sure of the cam size, I'm seeing different videos from you guys but nothing helps indicate how to determine the correct size of the cam, so I can get the right part. it seems that my stack-able is not being made anymore, or so it would seem...so I'm concerned that these videos may not apply...help, please

Henry for Model Number 131605901

Answer Hello Henry. We will need your model number to help you with the cam size. Please post your model number with a new question on the parts page. Thank you. http://www.appliancepartspros.com/modelnumber_locator.aspx

Was this helpful?

Yes

1 Answer

My kenmore agitator isn't agitating properly. I've removed the whole thing but can seem to get to "dogs" which I think may be the problem (thanks to some previous posts). I would appreciate help with how to disassemble agitator (top part) to get to the dogs.

Henry for Model Number 131605901

Answer Hello Henry. Here is a link to a video to show you how to remove the dogs. Hope this helps. http://www.youtube.com/watch?v=ensJz0h6wLM

Was this helpful?

Yes

1 Answer

Above the agitator is a hollow shaft with fins on it. Above this is the softener cup and cap. At some point everything but the lower agitator "popped" off. Probably from an unbalanced load. I can't seem to get it back together. I might be missing parts. I no longer have the flat cap. How do I get it back together?

Kevin for Model Number 41797922700

Answer Hello Kevin. Based on the information you provided, it sounds like the agitator 131605901 is bad and will need to be replaced. Hope this helps.

Was this helpful?

Yes

1 Answer

Customer Questions and Answers for Agitator by Frigidaire

Agitator

Questions & Answers

Most Interesting | Latest Questions