How do I change refridirator water filter head?
To replace the water filter head 218893201 you would first shut off water. Remove the 2 screws that are holding it in place, they are 1/4" hexhead. Once removed there are 2 compression fittings attached to the water lines. Push in on the ring around the tubing and pull the line out. Install in reverse.
Where is the water filter for this model?
Answer Hello John. The unit does not come with a internal water filter. However you can use a in line water filter part number 4378411RB. Thanks!
I have a pretty new water filter and the base filter looks good but water runs very slow out of the dispenser. I had very hard water for years but now have a softener. could the valve need replacement.
Answer Hello John,
You will want to check water valve to make sure that the water is flowing through the valve properly. Check the water reservior to make sure that the reservior does not have build up causing the water to flow slow. Double check to make sure that all the lines are reconnected properly.
There were no instructions or schematics on how to replace this part - 240396002 There were 21 questions which dealt with with difficulty but none with the actual procedure to replace. Can you please provide me with this informaiton? Tks, Steve
Answer Hello Steve. The housing mounted in the food compartment along with the light
and damper assembly must be removed as well. To remove the Control Housing Assembly, remove the
three screws across the front control box and the two
screws located in the rear control box. After removing
cover over water line on front filter models, remove the
screw from the back of the control box. Drop the housing from the unit down to access the lines going into the back of the filter base. Then access the lines coming into the base of the filter head. Press in on the fittings and release the lines from the filter base. Then remove the filter base from the unit. Install the new filter base 240396002 in reverse order.
I moved recently. After hooking up a new 1/4" water hose and installing a new water filter, I only have a VERY small water stream in the door to fill a glass. There seems to be plenty of water pressure and flow at the frig water tube end. Any ideas of why the low water flow?
Answer Hello Phil,
I hate to bring attention to the manufacturers' mistakes, but in this case, to help you solve your issue, I must. It has been brought to my attention several times in the past 5 years or so, that the manufacturers have had some issues with the "curing process" of their filters. If they aren't "cured" properly, a new filter will actually allow less water to pass than an old, ready to be replaced filter. I proved this on my own refrigerator. I removed the "new" filter and reinstalled the old one I had just taken off and, WAH LAH, the water pressure actually increased. I purchased another new filter and the new filter worked fine. This may not be the case for you but, I had to mention it as it is a possibility. The other possibility is if the fresh food compartment is set too warm, since the fans don't run when the compressor is off, the cold air will migrate to the bottom of the unit. This begins the freezing of the water tank. This is actually the only other thing besides a crimped water line that will cause the complaint.
How do I disconnect the water line from the base water filter or the AP3687338?
Answer Hello Mike. You press in on the plastic fittings where the hose connects to the base. Once pressed flat, the lines will pull out of the base 240396002.
Hi, I am trying to take off the water filter housing in side the fridge. I took off the four philips head screws but cannot unscrew the large screw behind the air filter housing. How can i release that screw? I do not recognize the type.
I am trying to replace the water filter base because i am not getting any water through dispenser. Thanks
Answer Hi Steve. Try disconnecting the water line connection under the freezer door. The John guess fitting has round release clips at each end. Press them in as you pull out the lines. Then put the fridge tubing in a deep pan and command for water now. Has the water tank frozen part # 241532006 behind the crisper drawers? Remove it and thaw it slowly in a warm sink water. Set both controls mid way as freezer air can migrate from the bottom of the freezer and back through the air rtn. which is a fixed oval grill. Examine all of this. As far as the large screw, use a plastic putty knife in between the cabinet wall and the housing part # 241755201. Apply light outward pressure as you are removing the long screw. Thank You.
Have water to filter housing installed new filter have no water going in filter.
Answer Hello Tom. Based on the information you provided, it sounds like the water filter base 240396002 is bad and will need to be replaced on the unit.
Water is dripping from the Puresource2 water filter housing drain holes do I replace the water filter base or the water valve?
Answer Hello MDL. Based on the information you provided, it sounds like the water filter base 240396002 is bad and will need to be replaced. Hope this helps.