Questions and Answers for Frigidaire 316207510 Oven Control Board

Total
$0.00

Our Price	$117.54
Compare At	~~$141.05~~
You Save	$23.51

I have a Frig Flat-top oven. The burners work without problem but when we turn on the oven/broiler, it doesnt work.There is an audible "click" like it wants to work but niether element gets even warm. Was told that the best idea for repair is to replace the "EOC" Is that accurate?

Shawn T

Answer Shawn, You will want to check to make sure that the thermal limiters on the unit are not bad. Check at the EOC for voltage between L1 and bake. There should be 120 vac at this point and if not then the EOC is bad.

Was this helpful?

Yes

1 Answer

I NEED TO INSTALL THIS CIRCUIT BOARD AND NOT SURE HOW TO REMOVE OLD ONE AND OR REPLACE WITH THE NEW ONE. ALSO DIDNT BUY A NEW OVERLAY SO WANT TO REUSE OLD ONE

Suzette for Model Number FEF365BWG PART # AP3586196

Answer Suzette, " To remove the electronic oven control: 1. Disconnect power from the range. 2. Remove the back panel from the backguard. 3. Disconnect the wires and harness from the control board. 4. Remove the four screws. (One from each corner)". Reverse the procedure and test the control. If you're going to be using the original overlay, you will need to be "extremely" careful removing it from the original control. You may even wish to warm it with a hair dryer to keep it flexible and loosen the adhesive. They have a tendency to wrinkle and roll, and usually don't have a pleasing appearence when installed.

Was this helpful?

Yes

1 Answer

When we tried to turn on the oven there was a loud pop then nothing worked. the top part works fine but when we turned the breaker back on all it does is beep and flash F1.

Angela for Model Number fef365bwe

Answer Hello Angela, F1 Control Failure Shorted keypad. Internal checksum may have corrupted control relay shorted or bad probe. Check probe and probe wiring and replace if bad. Power off for 30 seconds. If fault returns replace the control.

Was this helpful?

Yes

1 Answer

My range works just fine, but now the display is not working, so the oven will not work. Everything has worked with this stove perfectly until now, but I don't want to have to buy a whole new stove if I don't need to. Could it be that all I need is AP3586196 ?

Isaac

Answer Hello Isaac. Test for power to the clock on the unit. If there is power there, and the clock does not light up, you will need to replace the clock assembly 316207510. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Was this helpful?

Yes

1 Answer

bake element or top elements not working. clock working fine but when i try to turn on any other stuff doesnt heat up. when i turn the onven it says is on but nothing happens. do i need to replace the electronic oven control or what could it be?

Raciel for Model Number fef365bwf

Answer Hello Raciel. Test for power coming from the clock to the elements. If there is 240 volts to the unit, but none coming out of the clock to the elements, you will need to replace the clock assembly 316207510. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Was this helpful?

Yes

1 Answer

my oven or broil does not heat up at all but the control board shows it is working. Ihave replaced the temp. probe but still nothing what now?

Jb for Model Number fef365bwf

Answer Hi JB. The pictorial breakdown does not show a oven thermostat. So double check and see if you have 240 vac at the terminal block and 120 vac between L-1 and L-2 and neutral. If all the wiring is tight and at the elements also, The clock control needs changed. It is part # 316207510. Thank You.

Was this helpful?

Yes

1 Answer

If replacing the clock /timer (computer board) in the back of stove. Does the front clock panel also need to be replaced?

Sandy for Model Number fef365asg

Answer Hello Sandy. Yes, if you are replacing the clock 316207510, you will need to replace the overlay 316220800. Hope this helps.

Was this helpful?

Yes

1 Answer

Customer Questions and Answers for Oven Control Board by Frigidaire

Oven Control Board

Questions & Answers

Most Interesting | Latest Questions