Customer Questions and Answers for Control Board by Frigidaire

Elrodvoss for Model Number agq6700fs2

Answer Elrodvoss, If the end of cycle chime is buzzing for 30 seconds and then intermittently through the cycle then the control board would be faulty and need to be replaced. 

Steve for Model Number AEQ6700FS0

Answer Hello Steve. if the unit is stuck on loc, you will need to make sure the buttons are making good contact with the new control board to clear the code. 

Eric for Model Number aeq6000es0

Answer Hello Eric. If the board is new and still does not work, you may have a wiring issue. You will need to test and see where you are losing power at in the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html 

James for Model Number Frigidair dryer model # GLGQ642AS3

Answer Hello James, The timer 131930600 would be the cause and would need to be replaced. 

Debbie for Model Number AEQ6000ES1

Answer Hi Debbie. You have a stuck button that you need to try to clear. If you cannot unclear the code then replace the control board part # is134557201. Thank you. 

Bill for Model Number AEQ6000es2

Answer Hi Bill. Tcode means that the control " lock " is activated.READINGERRORCODES 1. Press and hold the Select and Cancel buttons simultaneously for 6 seconds to reset control. The buzzer will sound 1 time and “rES” will be shown briefly in the display. 2. Immediately after, rotate cycle selector knob 2 turns counter-clockwise to the third position from the top, and then press and hold the Select and Cancel buttons simultaneously for 6 seconds. The control will enter Field Test Mode, the buzzer will sound 3 times, and the digital display will alternate between “Fld” and the firmware revision number (ex. “r03”). 3. Rotate the cycle selector knob 2 turns counterclockwise. The error code will appear in the digit display. Troubleshoot problem by using chart below. Tomove on to the next code, press the Options button. To clear code, press the Select button. Code will be cleared when mode is exited. To exit this mode, simultaneously press and hold the Select and Cancel buttons for 6 seconds. NOTE: During normal operation, the displaymay show: “ad” - dryer is in an auto dry cycle. “dn” - cycle is done in auto dry. “PF” - a power failure to the board has occurred. “Err” - an error has been detected. “LOC” - control lock is activated. “PAU” - cycle has been interrupted. Failure code chart Failure code Fault condition Action E 10 Communication failure. Clear code, exit mode and start dryer. If the error persists, replace the control board. E 11 Communication failure. Clear code, exit mode and start dryer. If the error persists, replace the control board. E 12 Communication failure. Clear code, exit mode and start dryer. If the error persists, replace the control board. E 24 Shorted control thermistor. Remove wires from the control thermistor. Measure resistance of the thermistor. If the reading is not 50K(+/- 10%), replace thermistor. If the reading is within 50K (+/-10%) check wiring between thermistor and electronic control. If good, replace electronic control. E 25 Open control thermistor. Remove wires from the control thermistor. Measure resistance of the thermistor. If the reading is not 50K(+/- 10%), replace thermistor. If the reading is within 50K (+/-10%) check wiring between thermistor and electronic control. If good, replace electronic control. 54 Failure code chart.READINGERRORCODES 1. Press and hold the Select and Cancel buttons simultaneously for 6 seconds to reset control. The buzzer will sound 1 time and “rES” will be shown briefly in the display. 2. Immediately after, rotate cycle selector knob 2 turns counter-clockwise to the third position from the top, and then press and hold the Select and Cancel buttons simultaneously for 6 seconds. The control will enter Field Test Mode, the buzzer will sound 3 times, and the digital display will alternate between “Fld” and the firmware revision number (ex. “r03”). 3. Rotate the cycle selector knob 2 turns counterclockwise. The error code will appear in the digit display. Troubleshoot problem by using chart below. Tomove on to the next code, press the Options button. To clear code, press the Select button. Code will be cleared when mode is exited. To exit this mode, simultaneously press and hold the Select and Cancel buttons for 6 seconds. NOTE: During normal operation, the displaymay show: “ad” - dryer is in an auto dry cycle. “dn” - cycle is done in auto dry. “PF” - a power failure to the board has occurred. “Err” - an error has been detected. “LOC” - control lock is activated. “PAU” - cycle has been interrupted. Failure code chart Failure code Fault condition Action E 10 Communication failure. Clear code, exit mode and start dryer. If the error persists, replace the control board. E 11 Communication failure. Clear code, exit mode and start dryer. If the error persists, replace the control board. E 12 Communication failure. Clear code, exit mode and start dryer. If the error persists, replace the control board. E 24 Shorted control thermistor. Remove wires from the control thermistor. Measure resistance of the thermistor. If the reading is not 50K(+/- 10%), replace thermistor. If the reading is within 50K (+/-10%) check wiring between thermistor and electronic control. If good, replace electronic control. E 25 Open control thermistor. Remove wires from the control thermistor. Measure resistance of the thermistor. If the reading is not 50K(+/- 10%), replace thermistor. If the reading is within 50K (+/-10%) check wiring between thermistor and electronic control. If good, replace electronic control. 54 Failure code chartREADINGERRORCODES 1. Press and hold the Select and Cancel buttons simultaneously for 6 seconds to reset control. The buzzer will sound 1 time and “rES” will be shown briefly in the display. 2. Immediately after, rotate cycle selector knob 2 turns counter-clockwise to the third position from the top, and then press and hold the Select and Cancel buttons simultaneously for 6 seconds. The control will enter Field Test Mode, the buzzer will sound 3 times, and the digital display will alternate between “Fld” and the firmware revision number (ex. “r03”). 3. Rotate the cycle selector knob 2 turns counterclockwise. The error code will appear in the digit display. Troubleshoot problem by using chart below. Tomove on to the next code, press the Options button. To clear code, press the Select button. Code will be cleared when mode is exited. To exit this mode, simultaneously press and hold the Select and Cancel buttons for 6 seconds. NOTE: During normal operation, the displaymay show: “ad” - dryer is in an auto dry cycle. “dn” - cycle is done in auto dry. “PF” - a power failure to the board has occurred. “Err” - an error has been detected. “LOC” - control lock is activated. “PAU” - cycle has been interrupted. Failure code chart Failure code Fault condition Action E 10 Communication failure. Clear code, exit mode and start dryer. If the error persists, replace the control board. E 11 Communication failure. Clear code, exit mode and start dryer. If the error persists, replace the control board. E 12 Communication failure. Clear code, exit mode and start dryer. If the error persists, replace the control board. E 24 Shorted control thermistor. Remove wires from the control thermistor. Measure resistance of the thermistor. If the reading is not 50K(+/- 10%), replace thermistor. If the reading is within 50K (+/-10%) check wiring between thermistor and electronic control. If good, replace electronic control. E 25 Open control thermistor. Remove wires from the control thermistor. Measure resistance of the thermistor. If the reading is not 50K(+/- 10%), replace thermistor. If the reading is within 50K (+/-10%) check wiring between thermistor and electronic control. If good, replace electronic control. 54 Failure code chartFailure code Fault condition Action E4A The drying time has exceeded program Press Pause Cancel and SELECT buttons for time for cycle. 6 seconds to exit test modes. Position cycle selector to NORMAL, temperature selector to HIGH HEAT and touch START. Check for any thing that would extend dry times such as: no heat, restricted vent, blower fan blade broken or loose, dryer installed in closetwith solid door, or bad connection in moisture sensor bar cir cuit or dirty bars. If dryer operates normally but code returns, replace electronic control. E 5B No heat. Refer to flow chart dryer does not heat. E 68 One of the keys (buttons) is Enter function testmode and perform key stuck closed (active). (button) test to determine which button is at fault. Carefully free the and perform the test again. If button is free but the key struck code still exists, replace electronic control. E 8C High limit thermostat has trip to many times Check for blocked lint filter, blocked exhaust, in a certain amount of time. air leaks around air duct, broken blower fan blades,worn or loose drumseals, dryer installed in closet with solid doors or door seal not correctly seated. E AF Microcontroller has been reset Clear code, exit mode and start dryer. If byWatchdog timer. problem persists, replace electronic control. 55. The door switch is part # 134813601. Thank you. he LOC