24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Customer Questions and Answers for Control Board by Frigidaire

  1. Our Price $147.23
    Compare At $175.20
    You Save $27.97
     
    • Part Number: AP4354654
    • MFG Part Number: 137005000
    • Made by: Frigidaire
    Add to Cart

Questions & Answers

For Frigidaire Control Board (Part Number: AP4354654)

Ask a Question

Most Interesting  |  Latest Questions

I have a fridigaire front load washer model #FTF2140ES0. It appears to run thru all cycles with the exception of the spin cycles. I ran the self test and spins and drains properly. I also was able to run the self diagnostic and it give me error code 43 (control board problem> I am looking for confirmation that this is my problem. also what is the dificulty level to replace control board. I am pretty handy with tools but hardly dabble in appliance repair. Thanks, TK

Tk

Answer

1 person found this answer helpful.

Was this helpful?

1 Answer

I have the same problem where the other cycles work fine however when turned to normal the 8 hour delay light comes on and it won't start . If the pump is clogged would that not affect the other cycles ?

Joe

Answer

1 person found this answer helpful.

Was this helpful?

1 Answer

If the normal cycle on my Frigidaire front load washer model FTFB400GS0 will not run does it point to the control board as the problem.

Steve

Answer

1 person found this answer helpful.

Was this helpful?

1 Answer

When plug the power in, it will only beep 9 ttimes and all the lighs flash. Have to unplug the power to get to stop. Help

John A for Model Number ltf2140fso

Answer

Was this helpful?

1 Answer

Months ago I suddenly could not get my machine to work on the quick cycle. Then another couple of months went by and the Regular cycle wouldn't work. I can use the perm. press and the Large load cycle o.k, so far. I called the appliance store where I bought the machine in 3/06 and they said I needed a new control panel and use the machine until it died. I have had 3 previous times where I have had to have the control panel replaced. What is going on?

Janice R for Model Number FTF2140ES2

Answer

Was this helpful?

1 Answer

Our front load washing machine will randomly start beeping. The machine still functions but it is quite annoying. it has occurred when it is washing a load and when it is sitting idle. I have read other posts and they point to the control board. Before I order the part, I'd like to be sure that is what is going on here. Thank you.

Sharon for Model Number LTF2140FS2

Answer

Was this helpful?

1 Answer

My washer will run through all of the cycles but will not high speed spin in normal operation. In diagnostics mode it will high speed spin and all of the tests function correctly. The only thing I get is E43 error code. I have cleared the code and tried again. It just keeps giving me E43. I have replaced both the motor control board and the front button control board and I am still getting the error code E43. I am about at my wits end ready to throw this thing off of the back porch since I have put almost $300 into it and it is still doing the same thing as when I started. Is it possible the new front control board I got is bad right out of the box or could their be something I am overlooking. Thank you

Dennis W for Model Number FTF2140FS1

Answer

Was this helpful?

1 Answer

Out of the blue the washer will stop .. the lights will blink and the machine will beep. We can drain it and restart it but sometimes it will run all the way sometimes it won't. After it finishes .. out of the blue it will start beeping. I have looked online and found the error codes .. It blinks 44. We replaced the door switch and it's still doing the same thing. HELP

Kelly for Model Number Frigidaire LTF2140ES3

Answer

Was this helpful?

1 Answer

I've read posts with similar problems as mine, which is a error code E46, Control board problem. Within any cycle when it got to the spin cycle, in just sat there after the pump removed all the water and wouldn't spin. My only beef is that when I replaced the control board (Main control board) I continued to have the same exact problem. I also read that the door switch could be at fault so I checked that and discovered that it was bad. I checked all connections and am waiting for the door swich to come. I temporarily jumpered out the door latch contact that told the processor (Main control board) that the door was shut. It spun in the spin cycle but too slowly to get the water out of the clothes. After spending over 250 dollars on parts I'm wondering if I should just abandon the washer??? Any suggestions?

Ron for Model Number FTF2140ES0

Answer

Was this helpful?

1 Answer

Washer will not spin or tumble in early wash cycle, then shuts off as if done but clothes are full of water. When running the diagnostic test, the machine will tumble, spin at high speed and pumps water out. The error code 44 beeps (control panel) only after the last test. Should I trust the test and order the part?

Mike for Model Number Frigiaire LTF2140ES3

Answer

Was this helpful?

1 Answer

 

 
 
We are Safe, Secure, Dependable and Trusted
  • BizRate.com Customer Certified Site - Click to Verify