What is the correct icemaker to use in our Frigidaire? Thanks!
Answer Hello Vicki! Yes, the complete icemaker add on kit part number IM34 is the correct add on kit listed for your model F44N18CEW2. Thanks!
Will this model # fit in my frigidaire freezer model FPRH17D7KF1? What model of icemaker can I to install in my freezer?
Answer Hello Jose! If your freezer model number is FPUH17D7KF1, then you should purchase add on ice maker part number IM501. Thanks!
Ice maker model # m1 will not let water in.
Answer Hello Richard. You need to check and see if there is power going to the water valve when the icemaker cycles. If so, replace the water valve on the unit. If not, or the icemaker does not cycle, you will need to replace the icemaker on the unit. Also, check and make sure the fill tube on the unit is not frozen and clogged. If so, replace the water valve and thaw out the fill tube. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html
Do you have installation instructions for the ice kit ap3211717?
Answer Hi. There is not a instruction sheet, but I will talk you through it. It is a single valve that mounts on the inside of the back of the unit. Remove the back cover and you already have threaded female screw holes on the rt inner side wall of the cabinet. Use The brackets and hardware in the plastic bag to configure the tight and level valve mount to the side of the cabinet. Use the Plastic tubing and the Fitting connector on the tube end to adhere to the valve. Make sure the tube is firmly pushed up into the valve. This tubing follows up the back of the cabinet so it hooks to the end of the supplied ice maker fill tube. Use the small clamp on the fill tube after the plastic tubing is inserted into the fill tube all the way. Find the water valve electrical wire connector folded back in the existing condenser fan area of the harness. Plug it into the water valve. Remove the black rubber tip off the top of the water valve. This is where the house water line connects to supply the water to the valve. Use connectors and barrel sleeve connectors on the plastic line after you have placed a brass threaded nut on the line that threads into the valve. the barrel sleeve creates a tapered edge that tightens internally to the female valve threads tapered area for leak preventative measures. Do not over tighten, snug only- (ahead of a leak). The fill tube is placed through the hole cover (sticker) awaiting removal from the back of the top. Some twist approx. 30° and seal snug against the back so no outside air can get past the back wall. The fill tube comes all the way through the inside freezer evaporator cover hole (upper left side). Then the top of the ice maker mounts inside to the left side of the freezer wall. There are 2-holes for the top i/m mount tabs and one for the bottom i/m mount front tab screw. Start the 2 longer screws supplied in the bag and lay the shorter screw aside for the bottom mount hole. The wire harness plugs one way only into the back lt. side the ice maker (below the upper mount tabs). Then it is placed into the back of the freezer wall one way. Use a torpedo level on the ice maker level so it fills level correctly. Tighten the screws. Then place the ice bin below the ice maker. Cycle the i/maker bail arm up and down one time completely to trigger the fill. It can take from 4-24 hrs for the ice maker to chill down to cycle the first cube batch. You may want to dump this first batch altogether since it "flushes" any sediment that was left on the ice maker cube tray. Thank You.
Will this ice maker fit my Fridgadare refrigerator which was manufactured in 05/03?
Answer Hello, for the model number supplied you will want to order add on icemaker kit IM115. Thanks!
Which is this the right ice maker for this kelvinator? Never had one.
Answer Hello Lloyd! The add on icemaker kit that you will use on your model MRT15CSEW3 is part number IM34. Thanks!
What is the part number for just the wiring harness for the ice maker?
Answer Hello Deb! The internal harness is part number 3206349 and the external harness is part number 3206358. We have images available of each harness to help verify which one you may need, just click on the part numbers to view the parts information. Thanks!