24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Customer Questions and Answers for Probe,oven Temp by Frigidaire

  1. Our Price $26.14
    Compare At $31.37
    You Save $5.23
     Watch Video
    • Part Number: AP3363354
    • MFG Part Number: 316217002
    • Made by: Frigidaire
    Add to Cart

Questions & Answers

For Frigidaire Probe,oven Temp (Part Number: AP3363354)

Ask a Question

Most Interesting  |  Latest Questions

The f3 error code keeps appearing every time the oven is on for a prolonged period. I took the temperature sensor out. How do I check the resistance?

Bg for Model Number frigidaire gallery stove

Answer

1 person found this answer helpful.

Was this helpful?

1 Answer

I did a self clean which stopped after approx. one hour with the error F30. I unplugged the stove for 2 min to reset the control board. I plugged the stove back. The F30 error did not come back, but the display was PF (I guess Power failure). I pressed clear and the display was normal. I set the time. Everything works except 3 of the 4 elements on top. Bake and broil work as well as the front left element. I tested the sensor's resistance. It read 5000 Ohms. I don't understand how a problem with the oven ends up being a problem with the elements while the oven now works. Thank you for your help.

Gerard for Model Number The Model #: PLES389ECC Serial #: NF60212062

Answer

Was this helpful?

1 Answer

Electrolux ew30ew55gs2 oven. I replaced the temp sensor, control board and wave touch display. I have always cooked with Convection bake and recently started coking with bake mode. I see after it reaches 350F and U place food inside the temp drops and does not kick back on????? I see there are separate elements per the wiring diagram but your web site shows two elements. So how come it keeps temperature in Convection mode but Bake mode it doesn't???? Electrolux refuses to help When it was new a repairman called Electrolux for help so its not worth my paying a repairman whos just gonna call Electrolux. I appreciate some help.

Owen for Model Number ew30ew55gs2

Answer

Was this helpful?

1 Answer

We have a gas Frigidaire oven. When we turn the oven on more often than not the oven will not heat. Sometimes if the burners are also on it will heat, but even that is happening less and less. You can see the orange glow from the "pilot" but no heat.

Denise

Answer

Was this helpful?

1 Answer

Temperature in both ovens stays below set point. Preheat gets close to set temp then temp falls off 30 to 60 degrees below set point. Problem is with both ovens, but the upper oven temp diff is greater. I pulled the upper temp probe and it read 1087 ohms at room temp. any suggestions? Thanks.

Jim for Model Number FPET3085KFB

Answer

Was this helpful?

1 Answer

I have a Frigidaire gas/electric range/oven plcs389aca. The problem is with the oven temperature. When the oven is preheating the little bars that indicate the pre-heat level never go above one bar. After a while the oven will beep as if it has reached temperature. However the temperature does not get to the proper level, it is much too low. It used to display all of the bars when it was pre-heating. I checked the probe and it reads 1075 ohms at room temp. There are no error codes. The lower element gets cherry red while it is heating up so that seems to be ok. What else should I look to test/replace? Thanks for the help.

Nick for Model Number PLCS389ACA

Answer

Was this helpful?

1 Answer

Pre heat alarm will go off when temperature is reached, but heating does not shut off. Temperature will continue to rise to over 400°F. Does this sound like the probe or something else?

Richard for Model Number 790.46619503

Answer

Was this helpful?

1 Answer

My oven doesn't seem to maintain temperature, the preheat will go off, the red signal thing will go to the top, but it seems it is constantly going from the bottom to the top. Is this a control board problem?

Mike for Model Number Frigidaire GLES389EBA

Answer

Was this helpful?

1 Answer

Frigidaire PLES389ECB stove with Err Code F30. Replaced temperature sensor but did not help. What's next?

Shoji for Model Number PLES389ECB

Answer

Was this helpful?

1 Answer

Hello! The BROIL stopped working the other day, as in the element will not heat up. The EOC was replaced a couple months ago via Home Warranty for cost reasons, and all has been well up til now. Replaced BROIL element with new from your site with same result (nonfunction). Tested old and new element and getting resistance reads. Pulled temp probe out and tested, with no change on meter. Would this cause the issue or could it be a relay? Would like to know before ordering probe. Thanks so much, and you guys are the best!

Nate for Model Number PLES399ECB

Answer

Was this helpful?

1 Answer

 

 
 
We are Safe, Secure, Dependable and Trusted
  • BizRate.com Customer Certified Site - Click to Verify