Washer fill's with water, it washes and drains but does not rinse. Then it will not fill with water after that.
Rogelio for Model Number wwse5240g1ww
Answer Hello Rogelio. You will need to check and see if the cold water valve is bad and is not working on the unit. If so, it will cause the issue you are having with the unit. Make sure the screens are not clogged on the unit as well.
Please send instructions on how to take knobs off to install board. I saw a video that shows to use string or wire. What about the shafts? Please
John S for Model Number wwse5240g3ww
Answer Hello John,
We would not have instructions for removing knobs. The knobs would just pull straight off. The shaft would stay on the board.
Washer will not go into the spin cycle. Repairman stated that the inverter may need replaced.
Kathy S for Model Number wwse5240g0ww
Answer Hello Kathy. If the inverter is bad, you will need to order and replace the motor WH20X10058 on the unit.
When changing from wash cycle to spin, my machine makes a hard thumping noise. I took the front panel off and watched it during all of this. It tries to agitate and spin at the same time for a few seconds. Do I need a new control assembly or are there other problems?
Old Hippie for Model Number WBB4500G1WW
Answer Hello,
I found a service bulletin addressing the issue of agitation and spinning at the same time. It states to replace the mode shifter WH38X10017 and the motor WH20X10058. The motor has replacement recommendations determined by the part number listed on the old motor label. These part numbers seem to be the latest cross.
When I push the start button, the wash doesn't start.
Frank for Model Number WJRE5500G1WW
Answer Hello Frank. I would remove the control panel and make sure the assembly which holds the actual switch hasn't dropped out of it's clips. Many times all it takes is to simply "snap" it back in. If this isn't the case, the switch will have to be replaced. It looks like on this model that the switch is on the control so the control WH12X10404 would have to be replaced. Have a great day!
The start button on the right side of the machine doesn't make connection to start.
Frank for Model Number WJRE5500GIWW
Answer Hello Frank. I would remove the control panel and make sure the assembly which holds the actual switch hasn't dropped out of it's clips. Many times all it takes is to simply "snap" it back in. If this isn't the case, the switch will have to be replaced. It looks like on this model that the switch is on the control so the control WH12X10404 would have to be replaced. Have a great day!
I bought I new control board to replace the old one and it will not work. I have read from various sources that you need to put in a code for it to work such as turning the dial a certain way or holding in the start button for 3 seconds. Does anyone have the code for this so I can get it to work?
Kelly for Model Number WBB4500G0WW
Answer Hi Kelly. Try opening and closing the lid 5 or more times within 12 seconds. Hold down the start switch and turn the knob 1/2 rotation will put you in the seravice test mode. Do you have the service tech. sheet behind the control panel? If the lid test dont reset for you, Then change the lid switch part # WH12X10334. Thank you.
I bought this control board and installed it. It's still not working. Is there a reset code, or something I have to do to the washer to get this to work?
Kelly for Model Number WBB4500G0WW
Answer Hi Mark. Does the motor run without the pump or mounted to the transmission? Did you check the capacitor with a cap. meter? Is there a burnt spot inh the top of the capacitor? Are you getting 120vac to the motor from the timer? The capacitors had a bad series that blew open physically on top. This part # is 8572717. Thank you.Hi Kelly. Remove the power. Release the top panel hold down clips on the top of the front panel. Lift the top. Remove the front panel. Your motor is in front. On the motor top is a circuit board. There is a green led light that shoukld be blinking. Can you let us know (with the unit plugged in) how fast or slow the light blinks. And in what session does it blink in? There should be a tech. Sheet you can follow in behind the control panel also. Thank you.