Customer Questions and Answers for Mechanism Asm by GE

Corky for Model Number GSD6200J01BB GE Diswasher

Answer Corky, Check and make sure the float WD12X10047,float coverWD12X10051 and flood switch WD12X10151 did not get dislodged or damaged, re check and make sure there was nothing left in the sump filter and sump. Start the dishwasher and let it fill and run for 5 minutes, the water level in the center of the tub bottom should be 3/4 to 1 inch deep, at the least.based on your post water low water level or a damaged impeller WD19X10032 could be the issue. 

Dishwasher for Model Number pdw8280joiss

Answer Dishwasher, What is accumulating in the assembly, that you have to clean the impeller ? have you checked the the sump filter and cover WD22X10077 for damage or holes ? How often is the dishwasher used ? on some models if not used often enough, the motor shaft seal can dry out ans "stick" to the impeller seal and stall the motor. You should at least consider the impeller kit WD19X10032. App does not have access to, or sell "rebuilt" parts, if you wish to replace the motor you'd need the WD26X10015 assembly, which may be the best way to go. 

JEEPMAN47 for Model Number GE GHDA960K03BB

Answer Hello Jeepman47. If there is power to the pump, and it does not run and drain, you will need to order and replace the pump on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html 

Ken for Model Number GSD6200G00CC

Answer Hello Ken. If the water is spraying, but is not filling properly to spray correctly, you will need to replace the water valve WD15X10003 on the unit. If the water is not spraying or moving in the unit, then it sounds like the circulation motor WD26X10015 is bad and will need to be replaced. 

Dave for Model Number PDW7880J01SS

Answer Hello Dave. Here are the instructions from the manufacture. Hope this helps. 1. Remove lower rack from dishwasher. 2. Gently lift and rotate lower spray arm counterclockwise to remove. 3. Rotate nut hub counterclockwise to remove. Gently lift fine filter assembly up. Remove fine filter drain from sump. 4. Clean fine filter screen if soil is present. 5. To reinstall fine filter and lower spray arm reverse procedure. NOTE: When installing fine filter make sure the drain port of the filter is engaged with the drain for the fine filter. 

Steve for Model Number GSD6700G00WW

Answer Hi Steve. There is a pump seal and impeller kit part # is WD19X10032. Thank you. 

Steve for Model Number GSD6700G00WW

Answer Steve, You'll need to check the pump impeller assembly and seal WD19X10032 , you may have something going wrong(worn part, small article, etc). You will need to remove the filter plate and also check the sump assembly for debris. Good Luck. 

Barb R. for Model Number pdw 7880j01ss

Answer Hello Barb. Here are the instructions from the manufacture. Hope this helps. Drain Pump The dishwasher must be removed from its installation to gain access to the drain pump. The drain pump contains a one way check valve. Drain Pipe and Check Valve The dishwasher must be removed from its installation to gain access to the check valve that is inline with the drainpipe. 

John L for Model Number PDW7880j01ss

Answer Hello John. You can test and see if your getting power to the motor assembly. If so, you will need to replace it. You will need to unistall the dishwasher to do this repair. It should come with everything you will need. Hope this helps. 

Guest for Model Number pdw7033j01bb

Answer Hello. Check the float and make sure it is not stuck. Also test the valve and see if your getting power to it. If there is power to the valve, but no water, you will need to change the valve out. WD15X10004 Hope this helps.