24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Customer Questions and Answers for Pump Seal and Impeller Kit by GE

  1. Our Price $16.20
    Compare At $38.22
    You Save $22.02
     Watch Video
    • Part Number: AP631386
    • MFG Part Number: WD19X10032
    • Made by: GE
    Add to Cart

Questions & Answers

For GE Pump Seal and Impeller Kit (Part Number: AP631386)

Ask a Question

Most Interesting  |  Latest Questions

water does not pump out dish washer smells bad solenoid does kick in can turn pump impeller by hand found nothing on screen at pump

W R Fisher for Model Number ge gsd2000j01ww

Answer

Was this helpful?

1 Answer

I have a leak near the pump/motor and I assume that the problem is a seal. In following the guide to remove the old seal I am running into a different configuration. The video shows a blade while my unit has what looks like a spring wrapped around the shaft. It doesn't seem to unscrew. What's the trick to get it off? And is the kit listed compatible with my unit--your website suggests it is.

John for Model Number gsd880y-73ww

Answer

Was this helpful?

1 Answer

I am trying to get the pump apart before I order the rebuild kit,to be sure I can rebuild it. How is the plastic "screen" on the outside of the pump held in? Is it threaded or just pressed in? I don,t want to break it getting it out. It,s the part shown in the top left corner of the diagram for part# AP631386 that I,m talking about. Thanks for any help you can give me,Rod

Rod for Model Number Hotpoint HDB727K

Answer

Was this helpful?

1 Answer

The spring inside the replacement seal pulls the shaft of the motor out so far, the blades of the motor grind into the back plate after I screw on the impeller. Am I missing a spacer? I didn't see anything different from the original parts.

Clint

Answer

Was this helpful?

1 Answer

Hey guy's , I have a G.E dishwasher ( pot scrubber 600 ) about 10 years old , and lately the dishes on the top rack have not been getting clean ,I've even tried washing dishes with the bottom rack empty and only the top rack loaded , now I've even fooled the door latch and looked in side the washer while it was running and verified the pop up tube is coming up and water is pumping out but not sure if the water pressure is enough . Thanks .

Steve for Model Number gsd600g-01

Answer

Was this helpful?

1 Answer

This is the correct model number for my previous question....Pump leaks water when running. Will the impeller kit fix the problem? THANKS

Bryan for Model Number GSD3600G00CC

Answer

Was this helpful?

1 Answer

I just asked the last question regarding the top sprayer not spinning. In your response you mention the impeller and give part # AP631386. Is the top sprayer supposed to spin throughout the cycle whenever water is flowing to the bottom sprayer? Or is it only during a certain stage?

Travis for Model Number GSD880Y-70WW

Answer

Was this helpful?

1 Answer

The top sprayer has good flow and water comes out of it, but it doesn't spin. I've checked the line and removed the sprayer and cleaned, no obstructions. What causes this?

Travis for Model Number GSD880Y-70WW

Answer

Was this helpful?

1 Answer

My pump leaks water when solenoid activates drain at end of rinse phase. When valve closes, leak stops. Do I need pump seal and impeller kit or something else? Thanks for help!

Randy for Model Number GE gsd4940c02ss

Answer

Was this helpful?

1 Answer

How do you install the new shaft sleeve over the motor shaft without splitting it? It is obvious that it is an interference fit and requires some force to go on but in this case the interference was more than the sleeve could take. This sleeve was included in the kit, though it is not shown in the picture on the website.

David B for Model Number WD19X100032

Answer

Was this helpful?

1 Answer

 

 
 
We are Safe, Secure, Dependable and Trusted
  • BizRate.com Customer Certified Site - Click to Verify