Questions and Answers for GE WB17T10006 Terminal Block Kit

Total
$0.00

Our Price	$10.44
Compare At	~~$18.72~~
You Save	$8.28

There doesn't seem to be a kit available with the wire nuts and shrink tubing splice package for the GE WB17T10006 terminal block kit. I know you said to use either med or lrg high temp porecelain wire nuts, but what do you recommend in the way of shrink tubing to put over the wire nut splices? This GE unit is a built in, hard wired unit and will be difficult to get out and complete a repair, so I'd like to use the splice method near the terminal block, but I want to be sure I have the right high temp wire nuts and high temp shrink tubing. Thanks for your help.

Ben for Model Number JDP36B0D1CT

Answer Ben, The wire nuts, as long as they are ceramic will work for your unit. It is not necessary to put the shrink wrap on the nuts. The shrink is normally used in situations where there is moisture to keep the moisture from getting into the connection.

Was this helpful?

Yes

1 Answer

1 of the top heating elements burned out, I do mean burned out it went on fire. I am going to replace the element and the terminal block, but the the light on the stove to warn that a surface element is on stays lite now. By replacing the element and terminal block will the light go out? or do I also have to replace the temperautre control reostat?

Bruce for Model Number JBP24B0B4WH

Answer Hello Bruce. Most likely the switch will need to be replaced along with the element to get the light to shut off on the unit.

Was this helpful?

Yes

1 Answer

I have recently purchased a replacement baking element. The original one exploded while I was baking. When I went to replace it, I found that the spade terminal that connects to the baking element also was damaged. I have not been able to purchase the yellow wire that connects from the terminal block to the baking element. I am tired of being told that this is a non-consumer part. It is a simple wire with connectors. I have been using the stove top so I know that nothing else is damaged and I know I have seen the wire kit for sale but can not find it now. Can you please help me find the replacement wire?

Vicki Miller for Model Number RB757WH4WW

Answer Hello Vicki. The wires is not available, but you can order new terminals TJMA02875-1 and crimp onto the existing wire in the unit.

Was this helpful?

Yes

1 Answer

I can't find the model number for my stove listed, will this terminal block work? If I drop the o from bob4wh this in the number that comes up, is this right? Thanks for your help.

Jeff for Model Number JBP24BOB4WH serial # sd103436Q

Answer Hello Jeff! Yes, you will use model JBP24BB4WH in search for parts. Yes, the terminal block kit WB17T10006 is the correct replacement and will fit your unit. Thanks!

Was this helpful?

Yes

1 Answer

I thought I bought all the right parts put my element does not sit flush in the burner drip pan.

David for Model Number JSP34 WOW3WW

Answer Hello David, the burner elements for your model are, 6 inch element WB30M1 and 8 inch element WB30M2. Hope this helps!

Was this helpful?

Yes

1 Answer

The kit installed easily but the black block does not contain a brass assembly for the burners to plug into similar to the original.

Tom A for Model Number JSP26BW3AD drawing ref number 82

Answer Tom, The brass assembly, that the burners plug into are on the end of the wires. Basically you insert the brass connector end of the wire into the slots on the back side of the black plastic receptacle until they "lock" into place. Splice the new wires to the original wires using high temperature, porcelain wire nuts, if the wires are not long enough to reach the infinite switch, install the drip pan and insert the element ends into the slots of the new receptacle. Everything should be fine from there out. Thanks and Good Luck

Was this helpful?

Yes

1 Answer

I just purchased the terminal block kit AP3203326. Which of these 2 wire nuts is the the right size for the kit: AP3440631 or AP3440673?

Chris L. for Model Number JBP35EK1BB

Answer Chris, you will need the medium wire nut TJMA01165-1. Thanks!

Was this helpful?

Yes

1 Answer

How do I access where the stove end of the element wires in kit # WB17T10006 attach?

Ralph P. for Model Number J BP24G R1 WH

Answer Hi Ralph. Removew power. Then all coils and drip bowls. Then remove the connector bracket screws from all 4- burners. Then open the door and remove any hidden screws under each front corner. You can now lift the top and drop the prop rod down to support the top. Replace one terminal wire at a time so you have rewired it exactly original. Place all wires routed together so they do not have any contact under the burners to short them or to burn them out. Terminal kit part # WB17T10006. Thank You.

Was this helpful?

Yes

1 Answer

Does the wire nuts come with this kit?

Chris J. for Model Number RB757BC1AD

Answer Hello Chris! No, the terminal block kit WB17T10006 does not include the wire nuts. For medium wire nuts use part number TJMA01165-1 and for large wire nuts use part number TJMA01166-1. Thanks!

Was this helpful?

Yes

1 Answer

Customer Questions and Answers for Terminal Block Kit by GE

Terminal Block Kit

Questions & Answers

Most Interesting | Latest Questions