Questions and Answers for LG 4417FA1994G Drive Motor Stator Assembly

Total
$0.00

Our Price	$124.22
Compare At	~~$147.82~~
You Save	$23.60

Our LG washer model WM2277HB would constantly give an LE error. I replace the Stator assembly part # 4417FA1994G. After doing so the washer worked for a couple of cycles, but then started giving the LE error again. I have removed power for 24 hours or more, but as soon as I start another cycle (even Rinse and Spin), the LE error is back. If it's not the Stator assembly, what part should I look at replacing next or should I just look for a new washer? This washer is about 6 years old.

Chuck for Model Number wm2277hb

Answer Chuck, The hall sensor 6501KW2002A is the part that you would want to replace with the LE error code.

Was this helpful?

Yes

1 Answer

My LG Tromm model WM2277HB started flashing an LE error and the drum will not spin. I have replaced the Stator and Hall sensor. Once replaced the washer worked for a couple of washes after reseting but now is displaying the LE error again even after power is disconnected for 24 hours or more. All other functions of the washer seems to working. Thought about replacing the control PCB board but not sure if it will fix the issue. Any advice you can give me would be great.

Cc for Model Number wm227hb

Answer CC, You will want to double check to make sure that the stator is installed where it is not leaning to one direction or another. Check the harness going to the hall sensor and back to the control board for loose or broken wires. If this all checks ok then the control board would most likely be the failure.

Was this helpful?

Yes

1 Answer

hi our from loader washer started making a very loud and annoying whining and grinding noise while spinning then after a couple uses it seems to be locked up what would you suggest checking im thinking stator or some bearing in the drive unit . thanks for your help we just replaced the control board so we got some $$ in it and would like to fix it

Tom for Model Number wm0532hw

Answer Tom, A grinding noise during the spin cycle normally indicates that the bearings on the unit are bad and need to be replaced. Bearings part numbers are 4280FR4048L and 4280FR4048E. You would also need the seal 4036ER2004A.

Was this helpful?

Yes

1 Answer

I have an LG Tromm, it has started flashing an LE error code. When I turn it on it will fill with water, but when it is time for the spin cycle the drum will make a small jerk but will not be able to spin. Searching online I see that I might need to replace the hall effect sensor, does that sound correct?

Liz for Model Number LG Tromm Washer

Answer Liz, Yes, this is correct. The LE error code is an indication that the hall sensor has failed and needs to be replaced.

Was this helpful?

Yes

1 Answer

My LG acted like the motor would lock up or be overloaded. Eventually it gave me the infamous "LE" code. The suggestion was to test the stator and if it was ok, to replace the hall sensor. Which I ordered and installed. Now the motor does turn but it grinds and sounds overloaded and is making the stator smoke. I immediately disconnected the unit and tested the stator. It was hot but tested out 7 ohms on each leg. Now what the harness checks good. The control unit?. Any help owuld be appreciated.

Bob R for Model Number wm2277hw

Answer Bob, You will want to double check the installation of the stator and hall sensor. If the parts are not lined up properly or leaning a little it will cause the stator to grind and smoke.

Was this helpful?

Yes

1 Answer

I was told over the phone I needed the stator asy with hub. $200-$300 plus labor. How long does it take to replace? It is something a pretty handy person could do? And lastly, if it is hired out, what is an estimated price to replace the stator with sensor with labor? I am in a larger city so my price might be higher.

Charles for Model Number LG WM2277HW

Answer Hello Charles. Changing out the stator is not a difficult job. You would remove the rear cover of unit and remove the stator and rotor.

Was this helpful?

Yes

1 Answer

I have a Lg washer about five years old and it is in a very good shape. It stop working and I open at the back of the machine and push the drum four time and the machine wash five load. The next morning it went to the same problem. I replace the hall sensor. Now the machine does not agitate, or spin or wash the clothes. I follow the yellow, red and blue wires from the control board, I cant seems to get 120 come out. I unplug the wire harness and check the ac, I was not able to get 120 volt.

Chibe for Model Number wm2277hw

Answer Hi Chibe. You are on the right track. It will be advantageous to find the supplied tech sheet inside the cabinet to aid you in the diagnosis. It allows you to put the unit in a diagnostic mode which brings up fault codes and tells you which circuit needs assistance. Use a volt/ohm meter part # TJMA-DM1 to assist you in your diagnostics. What code's are showing now? Disconnect the motor connector and measure the terminal resistance. From pin # 1-2 , # 2-1 and # 3-1 you need to have 5-15 ohm resistance. If the measurements are different then these, replace the stator part # 4417FA1994G. Drive Motor Stator Assembly - This front load washer drive motor stator includes the rotor position sensor switch (RPS). For the RPS switch only order 6501KW2002A. Thank you.

Was this helpful?

Yes

1 Answer

My LG front load gives me an LE error code, I replaced the stator hall sensor, inspected the the magnets and all look good. The stator ohms out at 8 ohms on all 3 windings. I ohm’d out all the wires to the stator and sensor from the control board. It does work sometimes, if I put a meter on the control PCB at the motor connector when it works I get 50 to 70 volts AC, but while monitoring the voltage when it errors I see the meter go from 1.2 volts to 2 volts and a few seconds later it errors. The motor does not hum or vibrate so it appears it is not getting the voltage to turn. My recir pump is very noisy but it apprear to be working fine as I can see the water cascading down the front door. Do I have a bad control board or is the stator bad, or could it be the recir pump giving me a pressure fault. Thanks

Murray for Model Number LG WM0532HW

Answer Hello Murray. Based on the voltage readings you got, it sounds like the control board 6871ER1023R is at fault and will need to be replaced in the unit.

Was this helpful?

Yes

1 Answer

I was doing wash and several times restarted machine after in went into LE code (motor overload). A technician replaced the sensor less than a year ago. Now the LE code is back and the machine fills then when it should start washing it just sits and makes a humming and soft clicking noise for a while and nothing happens, the tub does not start to move or spin. I removed the stator/motor part with the sensor attached and thought I would just buy a new motor but your previous similar questions seem to suggest it is the sensor or the control panel and not the motor. Any ideas what this is. I do not want to start replacing parts on a 7 year old machine when I may be better off to just go out and buy a new machine for $500-600. Is 7 years for this type of appliance the trouble zone as soon as warranty expires?

Bev for Model Number WM2032HS

Answer Hello Bev. Based on the error code. You will need to check and make sure none of the magnets on the rotor are cracked. If not, you will need to replace the stator assembly 4417FA1994G on the unit.

Was this helpful?

Yes

1 Answer

My LG washer will not engage into the Spin Cycle. The washer just makes a humming sound like its trying to spin for a few seconds thanI get a flashing LE Code. I have unplugged my machine to reset it and it still doesn't help. I have also replaced the Drive Motor Stator #AP4438648(with RPS)as well as the Rotor Assembly #AP443865 and that did not solve my problem. Any suggestions on what my issue might be?

Matt S. for Model Number WM0532HW

Answer Hello Matt. If the stator and the rotor are new, you will need to replace the wiring harness 6877ER1016B on the unit.

Was this helpful?

Yes

1 Answer

Customer Questions and Answers for Drive Motor Stator Assembly by LG

Drive Motor Stator Assembly

Questions & Answers

Most Interesting | Latest Questions