24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Customer Questions and Answers for Gas Burner Valve Assembly by LG

  1. Our Price $124.35
    Compare At $147.98
    You Save $23.63
     Watch Video
    • Part Number: AP4457614
    • MFG Part Number: 5221EL2002A
    • Made by: LG
    Add to Cart

Questions & Answers

For LG Gas Burner Valve Assembly (Part Number: AP4457614)

Ask a Question

Most Interesting  |  Latest Questions

Igniter will not turn on but it looks fine. Would not getting gas cuse the igniter to not engage?

Greg for Model Number LG DLG2532W

Answer

Was this helpful?

1 Answer

My dryer does not heat at all. At first the igniter will turn on and no flames would not ignite at all what so ever. I was told by a technition that the issue what gas valve assembly. I replaced the gas valve assembly. tested the dryer and flames did ignite. However once I put the dryer back together, tested the dryer, the igniter will glow and heat up but no flames ignited at all what so ever. I took the front panel from the dryer, tested the dryer and the igniter glows but no flames are igniting. I checked the gas line and gas is flowing. All vents are clean from the dryer. Please Help!!!!!!!!!!!!!!!!!!!!!!!!!

Moreno for Model Number DLG 1320w

Answer

Was this helpful?

1 Answer

Originaly flame would not light at all. I found high limit sensor tripped, reset switch and flame would light and then go out in 15-20 seconds. Cleaned out vent system and replaced high limit sensor worked for three days and then found switch tripped again. Reset and tested several times but now flame is shutting down with out sensor reset button tripping. I just let it set for 5-10 min and flame lights again. I bypassed the thermostat switch and flame remains lit. The sensor has continuity but am wondering if the test indicates that sensor opens prematurely? Does this rule out a gas valve problem? Is it fairly common for sensor to test fine but open prematurely?

Jeff for Model Number dlg2522w

Answer

Was this helpful?

1 Answer

Ignitor glows, flame kicks on but only stays lit for 5-10sec. I have been told it is the gas valve assy. Is it that or a thermostat or something else? Thanks.

Erik for Model Number DLG5988W

Answer

Was this helpful?

1 Answer

Is gasket (ap5071358) part of this valve? Will I need to order the gasket and the valve together ? Gas Valve #AP4457614.

Jim for Model Number DLG0452W

Answer

Was this helpful?

1 Answer

Please help! I have posted twice on forum and nobody has suggestions. My gas dryer will run and burner will ignite and run for approx 30-60 seconds. It then stops heating and just blows cold air. The gas valves ohm out at 1900 ohms which is within the 1500-2500 ohm. I have tested all components and everything is within specifications. I disconnected the vent from wall in case the vent was plugged. What would you suggest I replace?

Philologus for Model Number DLG7188WM

Answer

Was this helpful?

1 Answer

My dryer when drying will make a buzzing noise just before the burner ignites. I have an extended warranty and had a service tech out. He said after hearing the noise it was the gas valve assembly. He replaced it never did any diagnostics on anything to prove his decision. Unfortunately it still has the same problem. I called them and they returned same tech. He says now its the gas pressure on the line coming in. I should call the gas company or plumber to check it out. Do you have any insights to what might be the problem?

Joe for Model Number DLG9588B

Answer

Was this helpful?

1 Answer

Dryer runs and heats when first started, then heat quits. I have run this with the front panel off to observe the gas system. The Igniter glows, but the flame does not start. I checked the resistance of the coils. Both read over 1900 ohms. Service Manual says to replace the valve when readings fare between 1500 - 2500 ohms. I have checked the other components associated with this circuit, and all seem okay. I checked the voltage on these coils when gas valve should be opened. Reads around 50 VAC. I assume I need to replace the gas valve, but I want to know if the coils are available as replacement parts, since the valve itself seems okay.

Phil for Model Number LG - DLG5932W

Answer

Was this helpful?

1 Answer

Here is my original question: My dryer will heat on manual setting up to 60 minutes. When I use the sensor settings, the clothes will not thoroughly dry. I replaced the ignitor recently. What could the problem be? I did as you suggested with the venting system, thoroughly cleaning it, but the heat still only works on the manual settings and not the sensor settings. Any other advice?

Kurt for Model Number dlg3744 Gas Dryer

Answer

Was this helpful?

1 Answer

I have a natural gas dryer but the burner is not turning on. The gas is on, but yet no fire. I tried firing up, but no flame. What could be the problem?

Sergio for Model Number Dlg2532w

Answer

Was this helpful?

1 Answer

 

 
 
We are Safe, Secure, Dependable and Trusted
  • BizRate.com Customer Certified Site - Click to Verify