Does part no ap4205725 door boot seal come with the wire ring location part no u0038?
Gregory for Model Number WF337AAL
Answer Hi Gregory. The door boot seal part # DC64-00802A does not come with the placement ring part # u0038. Thank You.
Thank you for the instructions on how to install part # DC64-00802A. The instructions refer to a figure that illustrates the instructions. Do you have a copy that you could post or forward? Thank you.
Julie for Model Number WF218ANW
Answer Hi Julie. Here is the information from the manufacturer. Hope this helps! Separating the Top Cover and Control Panel (Check Main- PCB and Sub-PCB): 1. Remove the 2 hexagon screws, which are at the back, fixing the Top Cover. 2. Separate the Top Cover by sliding it backwards and remove the 4 screws of the Control-Panel. Separate Detergent Box Button. 3. Press the Separate button to separate the Detergent Box. 4. Pull the Control Panel forwards to separate it. Tap the center of the Control Panel sliding it up to separate it. (Take care not to damage the Hook) 5. Separate the wire connected to the Main-PCB. Remove the 6 fixing screws and separate the Ass’y PCB. Seperate Sub-PCB from Main-PCB. 1. Pull the Diaphragm while holding the inside of the diaphragm with your hands. 2. Remove the 3 screws to separate the switch. 3. Remove the 4 screws at the top and the 2 screws at the bottom of the Front-Frame. To assemble, hook the Front-Cover onto the frame floor and then insert the assembly hook into the hole. 4. Push the lever and lift it up slightly to open the Front Cover. 5. Separate the remaining water removal hose (blue) from the hook and remove the 2 screws (red). 6. Press the Upper-Plate slightly with the screwdriver as shown in the figure, in order to separate the Front-Frame. 7. Remove the clamp from the back of the door boot. 8. Reinstall in reverse order. Thank You.
I am looking for instructions to replace the door diaphragm (part # DC64-00802A) on this washing machine. Thank you.
Julie for Model Number WF218ANW
Answer Hello Julie. Here is the information from the manufacturer. Hope this helps! Separating the Top Cover and Control Panel (Check Main- PCB and Sub-PCB): 1. Remove the 2 hexagon screws, which are at the back, fixing the Top Cover. 2. Separate the Top Cover by sliding it backwards and remove the 4 screws of the Control-Panel. Separate Detergent Box Button. 3. Press the Separate button to separate the Detergent Box. 4. Pull the Control Panel forwards to separate it. Tap the center of the Control Panel sliding it up to separate it. (Take care not to damage the Hook) 5. Separate the wire connected to the Main-PCB. Remove the 6 fixing screws and separate the Ass’y PCB. Seperate Sub-PCB from Main-PCB. 1. Pull the Diaphragm while holding the inside of the diaphragm with your hands. 2. Remove the 3 screws to separate the switch. 3. Remove the 4 screws at the top and the 2 screws at the bottom of the Front-Frame. To assemble, hook the Front-Cover onto the frame floor and then insert the assembly hook into the hole. 4. Push the lever and lift it up slightly to open the Front Cover. 5. Separate the remaining water removal hose (blue) from the hook and remove the 2 screws (red). 6. Press the Upper-Plate slightly with the screwdriver as shown in the figure, in order to separate the Front-Frame. 7. Remove the clamp from the back of the door boot. 8. Reinstall in reverse order. Good Luck!!
Do you have instructions to replace this seal for this model?
Jacque P. for Model Number wf218anw/xaa door seal part # dc64-00802a
Answer Hello Jacque! Here is the information from the manufacturer, hope they help!
Separating the Top Cover and Control Panel (Check Main- PCB and Sub-PCB):
1. Remove the 2 hexagon screws, which are at the back, fixing the Top Cover.
2. Separate the Top Cover by sliding it backwards and remove the 4 screws of the Control-Panel. Separate Detergent Box Button.
3. Press the Separate button to separate the Detergent Box.
4. Pull the Control Panel forwards to separate it. Tap the center of the Control Panel sliding it up to separate it.
(Take care not to damage the Hook)
5. Separate the wire connected to the Main-PCB. Remove the 6 fixing screws and separate the Ass’y PCB.
Seperate Sub-PCB from Main-PCB.
1. Pull the Diaphragm while holding the inside of the diaphragm with your hands.
2. Remove the 3 screws to separate the switch.
3. Remove the 4 screws at the top and the 2 screws at the bottom of the Front-Frame.
To assemble, hook the Front-Cover onto the frame floor and then insert the assembly hook into the hole.
4. Push the lever and lift it up slightly to open the Front Cover.
5. Separate the remaining water removal hose (blue) from the hook and remove the 2 screws (red).
6. Press the Upper-Plate slightly with the screwdriver as shown in the figure, in order to separate the Front-Frame.
7. Remove the clamp from the back of the door boot.
8. Reinstall in reverse order.
How do you replace DC64-01570A diagphram for this model?
Russell for Model Number Samsung WF 448AAW/XAA
Answer Hello Russell! Here is a link from our free repair forum with similar instructions for a different model on how to install the door boot. Hope it helps!
http://forum.appliancepartspros.com/washer-repair/155872-door-boot-seal-replacement.html
Do you have instructions to replace Samsung DC64-00802A Diaphram?
Russell for Model Number DC64-00802A
Answer Hello Russell. What is the model number of the unit your working on? Thanks.