24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Customer Questions and Answers for Atc Switch Mid Level by Whirlpool

  1. Our Price $35.87
    Compare At $52.12
    You Save $16.25
     
    • Part Number: AP4358828
    • MFG Part Number: W10184148
    • Made by: Whirlpool
    Add to Cart

Questions & Answers

For Whirlpool Atc Switch Mid Level (Part Number: AP4358828)

Ask a Question

Most Interesting  |  Latest Questions

I have an admiral washer in which i just changed the water inlet valves. In the middle of a wash the cold water stopped abruptly and i smelled a burning smell. Now only hot water works. I suspect the temperature selection switch, but I am not sure if it is that or the timer. I cannot afford to buy the wrong part. Any way to tell for sure? (I have a multimeter).

Bryan

Answer

Was this helpful?

1 Answer

Always get the same temp off water on the machine. The rinse cycle is the same temp as all the other cycles. When the knob is turned to cold water the same warm water comes out.

Jim for Model Number 110.29522801

Answer

Was this helpful?

1 Answer

The washer will only work with cold water. When I switch the knob from cold to hot, it still stays cold. I am not sure if it is the switch on the top of the washer or a valve located on the back of the washer. I can shut off the cold water into the washer and just let hot water into the unit, and I will get hot water. Do you have an idea as to which part it would be?

Kate for Model Number Whirlpool WTW5200VQ2

Answer

Was this helpful?

1 Answer

My Whirlpool washer washes well, but it only wants to wash on the extra large load side and not on small load. After washing is complete, I can hear the timer, but it will not let the water out of the tub and advance to the spin cycle???

Bert for Model Number Part No. 3952817 Rev. B

Answer

Was this helpful?

1 Answer

The machine only lets hot water in. When I select cold the washer just buzzes but no cold water goes in. I swap the hoses to put cold water in the hot connection and the same thing happens, only lets hot water in. I already changed the water valve and this did not fix the problem. Could it be the ATC switch? What else do you think?

Andy for Model Number WTW5300VW2

Answer

Was this helpful?

1 Answer

My washer is not filling with water. I have 120V through the water level switch and to the act sensor. At the solenoid I have 49 volts.

Paul

Answer

Was this helpful?

1 Answer

The washer is allowing cold water in on the hot temp setting. It used to run and cold water in and then just hot. Now the cold doesn't seem to shut off. So the water is barely warm.

Carol for Model Number ATW4475VQ1

Answer

Was this helpful?

1 Answer

I have a admiral washer, it will not fill with hot water. I have it set but when I turn it on a little comes out which is cold and then stops. The cold works fine.

Scott

Answer

Was this helpful?

1 Answer

Will only fill with hot water.

Lisa for Model Number wtw5300vw2

Answer

Was this helpful?

1 Answer

The ATC on my Whirlpool washer appears to be reversing hot and cold water. When in the Hot position, the water is cold. When in the Cold position the water is hot. This just recently started happening. I have verified that the water hoses are connected properly and that the water valve electrical connectors are correctly installed. Also, the thermistor on the water valve appears to be working correctly when measured at the connector to the ATC (about 40K ohms at room temperature and the resistance reduces when the valve temperature is raised). Can the ATC malfunction in this way? Seems very strange. Thanks for any suggestions you might have. Jesse

Jesse E. for Model Number Whirlpool WTW5800SW0 Washer

Answer

Was this helpful?

1 Answer

 

 
 
We are Safe, Secure, Dependable and Trusted
  • BizRate.com Customer Certified Site - Click to Verify