What is the cf capacity for the GSW9545JQ0?
Answer Hello Christine. We do not have the size of the unit. You will need to contact the manufacture for this information. Thank you.
Whirlpool Gold Washer does not complete cycle and either F4 or F3 error code appears. How can I find out what causes these error codes - and how to fix it? Thanks, Jack
Answer Jack, Here's the information you need : DISPLAY EXPLANATION AND RECOMMENDED PROCEDURE F3 LID SWITCH FAILURE
“F3” flashes and cycle signal beeps continuously if the lid was NOT opened after cycle was completed. The electronic board must detect that PAUSE/CANCEL was pressed during a cycle or the lid was opened at least once at the end of any cycle. This is continually tested to ensure proper lid switch operation. If “F3” is flashing, check continuity of the lid switch. With the lid closed, lid switch contacts should be closed. – With the lid open, lid switch contacts should be open. – If the lid switch is failed, replace it. – If the lid switch is good, replace the control board. NOTE: Beeper will sound continuously while error code is flashing.
F4 RECIRCULATE PRESSURE SWITCH FAILURE “F4” flashes and the cycle signal beeps continuously when the recirculate pressure switch is not working properly during the Catalyst, Wash or Soak cycle. If “F4” is flashing, check the following: – Plugged recirculate hose (black hose). – Plugged or disconnected air tube (clear tube). Wires to the recirculate pressure switch disconnected or not connected correctly.
– Failed recirculate pressure switch. Switch (black wire, tan wire) contacts should be open with pressure applied and closed with no pressure. NOTE: Beeper will sound continuously while error code is flashing. You should find your technical data/information sheet attached to the inside of the cabinet front panel or inside the control panel assembly, if you wish to conduct other tests and diagnostics. Thanks and Good Luck
How much is a repair manual for it and how do you remove the agitator from it?
Answer Hello John. 677813L is the correct repair manual for the unit. You will remove the cap from the center of the agitator and remove the locking bolt and lift the agitator out of the washer inner tub assembly. Hope this helps.
What is the cubic capacity of this top loader for Whirlpool LSQ8000LQ1?
Answer Hello Charles. We do not have this information. You will need to contact the manufacture of the unit for the capacity. Thank you.
Not sure if this model # is correct for my whirlpool, there is no model on the unit. It says whirlpool heavy duty super capacity...supreme. Anyhow, it seems to agitate slow, but that's not my biggest concern. It is horrible in the spin cycle. It came to the point where I recently would have to rig the lid to stay open, and give the machine a push, in order to get it spinning well. Now, It hardly wants to spin at all, even with help. So, I flipped it over, expecting a bad belt...but I don't see a belt. I pulled 3 bolts to try and remove this large hunk of steel (transmission??) and I couldn't get that out of there either. Any ideas on a fix??
Answer Steven, There are a couple of things you'll need to check. The drive coupling, and the clutch and brake assembly(s),and the spin tube and bearings for excess wear 285753A 285785 285792 . The "slow" agitation could be due to a slipping agitator due to partially stripped splines on the inside of the agitator 3347288 . Heres a post from the APP Repair Forum that should be helpful, [http://forum.appliancepartspros.com/washer-repair/3265-replacing-direct-drive-washer-brake-shoes.html] Thanks and Good Luck
How do you remove the top side panels?
Answer Hello Mary. Disconnect the power to the unit. Release the two clips under the corners of the control panel securing the control panel. You can use a flat blade putty or butter knife to do this. Pull the control panel forward and flip it backwards. Next unplug the lid switch and remove the two brass colored clips securing the cabinet to the back wall using a flat blade screwdriver to pry them out. Pull on the front of the cabinet and slide the cabinet off the frame of the washer. You can now access and replace the part needed. Reinstall in reverse order. Hope this helps.
My machine fills up with water, but the wash cycle will not start. What is the problem?
Answer Hello Dee Dee. You will need to check and see if the lid switch 8318084 is bad on the unit. If so, it will cause the problem you are having. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html
How to a gasket?
Answer Hi Patrick. This repair service manual should help, part # 4313896. Thank You.
What is the capacity?
Answer Hello Cliff. We do not have that information. You will need to contact the manufacture for the capacity. Thanks.