24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Customer Questions and Answers for Belt by Whirlpool

  1. Our Price $25.53
    Compare At $31.06
    You Save $5.53
     Watch Video
    • Part Number: AP5324119
    • MFG Part Number: W10388414
    • Made by: Whirlpool
    Add to Cart

Questions & Answers

For Whirlpool Belt (Part Number: AP5324119)

Ask a Question

Most Interesting  |  Latest Questions

I have had this front load washer for about 7 years with no maintenance other than my wife's ritualistic cleaning of the seal etc. to keep it smelling clean. It operates normally but, when beginning to spin and when slowing down it has a horrible knocking noise that varies due to speed. The washer is level and on a slab surface so I know it has to do with a worn out component. I am getting a belt and would like to know what additional items I should get. By the way my wife uses it at least twice a day everyday. It has had a hard life but she loves it.

Daniel P for Model Number GHW9300PW4

Answer

Was this helpful?

1 Answer

My belt has been falling off and now it has snapped. When I put the belt back on the pulley, before it snapped, it seemed to track toward the tub and not stay in line. I noticed that the belt has ridges that fit with the motor pulley and the tub pulley has no ridges. Also, I checked the tub pulley and motor pulley, both seem to be firmly attached. Other than the obvious need for a new belt, is there anything I can do to get this belt to track properly so I do not have to continuously replace it? This will be the second belt this washer has eaten in two years.

Phil for Model Number GHW9100LW1

Answer

Was this helpful?

1 Answer

the belt keeps coming of, i have tightend the nut but still it comes of. Also the machine is vibrating more than eaver. do i need a new belt?

Alan for Model Number whirlpool washer awo/r4205

Answer

Was this helpful?

1 Answer

I replaced the belt on this washer around 8 months ago. It started spinning slow so I opened the back and saw the belt completely off both the tub and motor pulleys. I replaced the belt again and noticed that when it is spun by hand, it tracks toward the tub. How do I keep it tracking straight. I looked at both pulleys and the motor mounts all SEEM to be ok. I did notice that the motor pulley and the belt both have ridges and the tub pulley is flat. Tub pulley was replaced about 8 months ago as well.

Phil for Model Number GHW9100LW1

Answer

Was this helpful?

1 Answer

my washer will not pump the water all the time what should i look for

Bob R for Model Number 11042832201

Answer

Was this helpful?

1 Answer

This belt is really hard to put around both pulleys. Are there any special tools I should be using or another easier way to install?

Donna for Model Number GHW9150PW4

Answer

Was this helpful?

1 Answer

I have a Kennmore HE3 front-loading washer. About three weeks ago, the belt slipped off. I retightened the nut holding the pulley on and put the belt back on. It worked until today. (By the way, with a household of 10 and their friends, we do a lot of laundry!) The belt had slipped off, gone behind the pulley and broke. I took the nut and pulley off. The bolt where the nut goes seems solid (no play, etc.) The pulley has play about 1/2 inch left and right without the nut on. I know I need a new belt, but do I need a pulley too? I don't know what the hole in a new pulley is supposed to look like. I've seen no grease/oil leakage anywhere either, just the black residue from the old belt. Can I put a washer between the nut and pulley to keep it tight? Thank you very much!

Roy M. for Model Number 11042822202

Answer

Was this helpful?

1 Answer

I just bought the belt and I was able to get it installed. Now I can't get it centered. I don't know if I put it on wrong or what. Thanks for your help. Coty

Coty for Model Number wfw9750ww01

Answer

Was this helpful?

1 Answer

Note: This question is for the older version of this part, but we thought you might still find it helpful

I occasionally get the error #06 at the beginning of the final spin cycle. Could this be caused by an old belt? The unit is 6 years old and started doing it intermittently about a year ago.

Mike for Model Number ghw915pw

Answer

Was this helpful?

1 Answer

Note: This question is for the older version of this part, but we thought you might still find it helpful

i HAVE A WHIRLPOOL WASHER MY BELT IS BROKEN i NEED TO KNOW HOW TO TAKE THE BACK BOARD OFF I TOOK THE SCREW OFF EXCEPT FOR THE TOP HOWEVER THE BACK DOES NOT WANT TO COME OFF IS THERE SOMETHING i AM MISSING HOW IS THERE A PICTURE SOMEWHERE THEY SHOW HOW TO TAKE THE BACK OFF. THANK YOU FOR YOU HELP Michel

Michel for Model Number GHW915PW1

Answer

Was this helpful?

1 Answer

 

 
 
We are Safe, Secure, Dependable and Trusted
  • BizRate.com Customer Certified Site - Click to Verify