Questions and Answers for Whirlpool W10111616 Cntrl-Elec

Total
$0.00

Our Price	$192.54
Compare At	~~$231.05~~
You Save	$38.51

My maytag bravos stopped drying so I checked heating element it had a coil burnt out there were no codes at this time. So I replaced heating element the thrmst-fix and thermistor. Now iam getting code F1 primary control is this common on this model?

Kenneth for Model Number med6400tb0

Answer Hello Kenneth, This issue is not really a common problem. It is something that can happen at any given time but the machine control [w10111616] will need to be replaced.

Was this helpful?

Yes

1 Answer

Is this part, W10111616, the part I need to get my dryer working since it is now flashing F1? Where can I find detail on your return policy? I've never tackled a repair like this and want to buy with confidence that if I have to abandon this mission, I am not out $170+.

Dennis for Model Number WED6600VWO

Answer Hello Dennis, The part W10111616 Control is the correct control to replace for the F1 Error code. Our website tells about the warranty and return policy.

Was this helpful?

Yes

1 Answer

Control display works fine when turn on and timer works. Drum does not turn-belt and motor turn easy. I suspect control board assembly defective.

Ralph for Model Number wed6600vmo

Answer Hello Ralph, With the display working you should check the continuity of the thermal fuse 3392519. If the thermal fuse blows then you will have display but no motor or heat. You may also want to check the thermostats and other thermal fuses W10169881 as well. You will also check the venting from the blower wheel all the way to the outside of unit to make sure it is clear. This is the most likely cause of the thermal fuse failing. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Was this helpful?

Yes

1 Answer

I just replaced the electronic control consel on the top of the dryer because the dryer on switch would light up but not turn on the machine. Now, it flases F-2 and makes a clicking noise. I have power to everything and F2 keeps flashes in the window. Any idea what I need to do?

Robin for Model Number MED6600TQ0 Maytag Bravo Steamer Dryer

Answer Hello Robin. The error code is for a stuck button on the console W10170903. Check and make sure the cables are installed properly going between the two parts.

Was this helpful?

Yes

1 Answer

No heat from dryer. Everything else works fine.

Daniel for Model Number mde9306ayw

Answer Hello Daniel! This answer was located on our Repair Forum, this is a free service in which technicians will assist with answering repair questions for our customers. Please use this link to assist in your repair. Hope it helps, thanks! http://forum.appliancepartspros.com/dryer-repair/247828-dryer.html

Was this helpful?

Yes

1 Answer

Hello. I am trying to fix a friends whirlpool dryer. I have no power to the display board, but the light inside comes on. Would the problem be part number ap4316847? Thanks

Nick

Answer Hello Mick. If there is power to the electronic control W10111616 and there is no power to the interface, then you will need to replace the electronic control. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Was this helpful?

Yes

1 Answer

My MED6600TQ0 Maytag Bravo gets too hot. It is even extremely HOT on air dry. At first it would not run, so I replaced the thermal fuse 3392519. It ran but still got HOT. I cleaned the vent (not much in there either), it still ran HOT. I replaced the thermostat and thermal cut-off AND thethermister. The relay is shorted on the control board. I got a new control board but I can not remove the connector to the heater relay 2 - like it is welded on - is there a trick to remove this connector? - do they sell these connectors?

Rick for Model Number MED6600TQ0

Answer Rick, which relay is shorted on the control board, the heater relay we hope ? Have you checked for a shorted heater element, when you checked the thermostats and thermistrers ? You may need to use a small(1/8") flatblade screw driver and pry up and out on the wire connector, or a pair of needle nose pliers and grasp the connector and pull it off. Thanks, and Good Luck.

Was this helpful?

Yes

1 Answer

My MED6600TQ0 Maytag Bravo gets too hot. It is even extremely HOT on air dry. At first it would not run, so I replaced the thermal fuse 3392519. It ran but still got HOT. I cleaned the vent (not much in there either), it still ran HOT. I replaced the thermostat and thermal cut-off. No luck. What next?

Rick for Model Number MED6600TQ0

Answer Hi Rick. It sounds like the thermister part #8577274 could be out of range. It senses blower heat temperature, I would suggest changing that part if it is too warm up on the top of the sides of the dryer (also if the top is Hot). This part basically tells the machine control board how long to run the heater. Hope this helps. Thanks.

Was this helpful?

Yes

1 Answer

Customer Questions and Answers for Cntrl-Elec by Whirlpool

Cntrl-Elec

Questions & Answers

Most Interesting | Latest Questions