24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Customer Questions and Answers for Electronic Control Board by Whirlpool

  1. Our Price $220.33
    Compare At $264.40
    You Save $44.07
     
    • Part Number: AP4370662
    • MFG Part Number: W10141364
    • Made by: Whirlpool
    Add to Cart

Questions & Answers

For Whirlpool Electronic Control Board (Part Number: AP4370662)

Ask a Question

Most Interesting  |  Latest Questions

The icemaker makes good ice for about 3 to 4 cycles. It then has an operation without putting any water in the reservoir, but the compressor kicks on and it goes into a freeze mode. The evaporator gets very cold, usually the water line then freezes and it tries to have a normal cycle after that but not much water gets into the reservoir. In addition when the ice is being made for about the last 2 minutes of the cycle, the water level gets so low the pump draws air into the line

Dan for Model Number KUIC15PRT

Answer

Was this helpful?

1 Answer

My ice maker quit working. The red eye on the control panel does not come on at all. Does this mean I need a new emitter board or what is the problem?

Gary for Model Number KSR525IKSS01

Answer

Was this helpful?

1 Answer

No power to cutting grid.

Billy. for Model Number mim1554zrs

Answer

Was this helpful?

1 Answer

"I have a Kitchenaid cabinet icemaker Mod KUIS18NNTS1It quit making ice suddenly. The recirculating pump is not working. There is 12 vac at the pin connector of the pump when it should be recirculating. That voltage goes away when I plug in the pump. Everything else works,The water reservoir fills, the evaporator gets cold, and heats on the harvest cycle. I've replaced the pump and the control board.

Jim for Model Number jimbloom@midco.net

Answer

Was this helpful?

1 Answer

I have a Kitchenaid cabinet icemaker Mod KUIS18NNTS1. It quit making ice suddenly. The recirculating pump is not working. And there is only about 2 vac at the pin connector of the pump when it should be recirculating. Everything else works,The water reservoir fills, the evaporator gets cold, and heats on the harvest cycle. Am I looking at a new control board? or is there something else that could be causing the pump not to com on. Jim

Jim B

Answer

Was this helpful?

1 Answer

When I ran diagnostics on my ice maker the optic control board was working fine and the ice maker needed to be replaced. I installed the new ice maker per instructions after I got it from appliance parts pros, and now the optic control board all the sudden shows deffective. Did I do something wrong? It was working ok before I replaced the ice maker.

Michael K for Model Number 2255433

Answer

Was this helpful?

1 Answer

My ice maker makes sheets of ice but the cutting grid doesn't get hot enough to cut the ice. I removed the cutting grid, cleaned it of any residue and also ran cleaner through the cycle but it still doesn't cut the ice. Any suggestions of what could be the issue would be appreciated. Thanks, Scott M.

Scott M. for Model Number Kitchenaid KUIS15NRTS

Answer

Was this helpful?

1 Answer

Ice maker stopped making ice all of a sudden after working fine for 4 years. I replaced ice maker assembly module and still no ice. No water filling ice tray and no movement of ice tray assembly. The ice maker control knob on right side of freezer is on and red light is blinking. Water flows well through water dispenser. How do I know if ice maker control is working? Should the red light be blinking? It still blinks when I turn to off position. It blinks twice, then pauses and then blinks twice again when in on position.I have control panel on fast ice and fast cool. I live in Florida and there has been high humidity lately and water condensing on doors. Thanks, Scott.

Scott S for Model Number whirlpool GD5RVAXVY01

Answer

Was this helpful?

1 Answer

This unit has an auxillary drain pump. When the unit is turned on, the water valve opens and over fills the water pan, then the water shuts off, the recirc pump starts and pumps for one minute then shuts off. The pan drain pump starts and pumps the water out in to the auxillary pump. The water valve opens and starts the process all over again. It just keeps going through the same process. I have also noticed when the auxillary drain pump starts, the interior light and the on/off light goes off for a second. Sometimes the auxillary pump never shuts off. I have replaced the water level sensor, bin and evaporator thermistor. Now I am beginning to think it is the control board.

Bobby A for Model Number KUIS18NNTB1

Answer

Was this helpful?

1 Answer

We just got this Ice Maker from a friend, but it does not seem to want to stop making ice. The unit will turn on, It will make ice, but it just keeps making ice. None of the buttons on the control panel work either. Any suggestions?

Derek S for Model Number KitchenAid KUIA15NLHS11

Answer

Was this helpful?

1 Answer

 

 
 
We are Safe, Secure, Dependable and Trusted
  • BizRate.com Customer Certified Site - Click to Verify