Why you dont have this parts?
Answer Hello Octavio. This part has been permanently discontinued by the manufacturer and we don't know of any source or replacement for the part.
Just recently, a high pitch whining sound has developed. The sound goes away when the refrigerator door is opened as the light/control display comes on. It will start back up again when the light/control display panel is off, even if the door is open, if the door light switch is not activated. Whether the compressor is on or off does not seem to make any difference. The noise sounds like a slightly fainter version of the beeping sound when the temperature control buttons are pushed, but it's a constant sound, not a beep.
I've also tried turning off the switch on the control panel and tried opening and closing the refrigerator door. When the panel is off, the noise is no longer there. Opening and closing the refrigerator door when the panel is turned off does not make any difference, there's no noise. The noise only seems to be there when the panel is on and when the panel is not lit.
The refrigerator and freezer seem to be working fine as everything still stays cold. I tried turning off the main switch behind the grill cover (per Kitchen Aid's instruction when I called them, waiting 10 minutes before turning back on to see if it helps) and the problem still persists.
The noise stays consistently on for the most part, but every once in a while, it will go silent. And then a bit later, it turns back on again. Just recently, The compressor has started to cycle on and off repeatedly. Also, at times, the display panel will not display correctly. It will intermittently flicker and sometimes not come on at all. Then it will go back to normal. Please advise which parts you think are broken and the possible remedy. Thank you.
It is hard to determine exactly which part has failed without knowing where the noise is emanating from. You will want to try to pinpoint where the noise is the loudest. It sounds like it could be a bad fan motor, so you will want to listen for the evaporator fan to check to see if this is the issue or the condenser fan motor. Also listen to see if it is coming from the control panel. If this is the case then the control is what is at fault and would need to be replaced.
I've been having trouble with the fridge staying cold for the last few months. I had a tech come out, we did all the diagnostic tests, and he ultimately told me that the main board (part# W10219463) needed to be replaced, to the tune of $600. He said that the board was no longer manufactured and had to be rebuilt. After further discussion he said that when they rebuild the boards, all they do is replace the relays. So I decided to buy the relays and replace them myself. I found the exact relays for a couple bucks each and replaced them, no problem. However, the unit still does not function properly. Now the alarm sounds continuously. Relays click, the condensor goes on, but there is no display or only a quick flash of the display when powering on. Are there other parts on the board that might be causing this that I can replace, or is it even the board at all? Should I just send in the board to get rebuilt at this point? Thanks for any help and advice.
Answer Hello Trevor,
It sounds like something has gotten crossed in the board which would cause the alarm to sound all the time. It would be better to send the board to have it rebuilt as they can test each component. They would also have a breakdown of all the parts of the board to repair it properly.
I have a Kitchenaid Built-in. The lights come on but nothing else. There is a beep every few seconds (faint) and nothing is working. Power comes to the invertor box and then to the compressor. What part do I need to replace?
Answer Hello Gil,
If nothing on unit is coming on then you want to check your main control board W10219463. If you are getting lights but nothing else then you may be stuck in defrost. Unplug unit from wall or turn off main breaker for 30 seconds to let control reset. When you turn back on check to see if unit comes on. There may be a 7 minute delay on the compressor. If it comes back on then you need to replace control board. If it does not then you still want to check to make sure control board output to components is there if not then you would still need to replace control.
Model KSSC42QMS01 Fridge. For the first few days of operation all is ok. Within a week the evaporator freezes over so that the fridge side becomes warm and freezer stays cold. The blend door is open. So far the electronic control board, the bi metal, the heater element, evaporator fan, condensor fan, and pc power board supply(on top of unit) have been replaced. The problem persists. I feel that the contol board (new one as well as old) is not letting the unit go into defrost.
Answer Hello Peter. Based on the information you provided, if the wiring is good, you will need to order and replace the electronic control W10219463. It is bad. This part has been permanently discontinued by the manufacturer and we don't know of any source or replacement for the part. However, you can send the board to Corecentric Solutions, Inc.
Attn: Rfr Dept 175 Wall St Glendale Heights, Il 60139-1956
Phone:866-737-2244 For Repair Options. Thanks.