24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Customer Questions and Answers for Electronic Control Board by Whirlpool

  1. Our Price $187.02
    Compare At $220.68
    You Save $33.66
     Watch Video
    • Part Number: AP5736909
    • MFG Part Number: W10525351
    • Made by: Whirlpool
    Add to Cart

Questions & Answers

For Whirlpool Electronic Control Board (Part Number: AP5736909)

Ask a Question

Most Interesting  |  Latest Questions

My washer threw a breaker I flipped the breaker back and the washer started the cycle back made it till there was three min left on the display and stopped. I took the front panel off and manually unlocked the door the cloths where dripping wet. There was no codes. I unplugged the washer tried to reset the washer and nothing happened the door locked and nothing else happened. I was told it was my control board so I replaced it. Now it will start a cycle it drains but doesn't spin and the door want unlock. And it will go through the cycle and when it gets to 4 min left on the display it will stop and want go any further. So I unplugged it and tried again an left it all night when I checked it this morning it was flashing 28 on the display.what do I need to try now

Tammy for Model Number Wfw8300sw04

Answer

Was this helpful?

1 Answer

I need some help figuring what parts to replace. The washer was in the middle of a cycle and tripped the breaker. I reset the breaker and the washer wouldnt do anything. the door wouldnt open and the washer had water in it. I unlatched the door from the bottom panel and took the wet clothes out. I drained down the washer and cleaned out the filter. then I ran a diagnostic test and got error codes f-28 and f-33. I tried running another cycle and the first time it filled with water and did nothing else. I drained it again and tried the same thing and nothing happened. Anyone know whats going on?

John for Model Number WFW8300SW03

Answer

Was this helpful?

1 Answer

Note: This question is for the older version of this part, but we thought you might still find it helpful

I'm getting the f1 error. What part would fix this and what would be the part number?

Russ S. for Model Number wfw8300sw05

Answer

Was this helpful?

1 Answer

Note: This question is for the older version of this part, but we thought you might still find it helpful

Location of temperature sensor.

Robares for Model Number wfw8300sw01

Answer

Was this helpful?

1 Answer

Note: This question is for the older version of this part, but we thought you might still find it helpful

We have a whirlpool duet. I recently replaced the water pump which lasted about a week before the f21 error code returned. I took it down and found a string(drawstring for warm up pants) blocking pump impeller. I grinned happily, pulled the string out, replaced the housing cover, started a rinse/spin to confirm operation. I then walked out of laundry room to brag to the wife about my washer repair prowess. One minor little problem.....this dumb*** forgot to reconnect the water hose on top of the pump. Naturally, when I heard water spraying all over everywhere, I ran back in and shut it down. Now, when you start a cycle, everything appears normal til you hit the start button. It then clicks and add a garment light comes on. Nothing happens after that til you disconnect AC power from it. Then it looks as if all is right, but it only clicks, lights add a garment.....rinse....repeat..Im assuming water got into the control module located on bottom. back right of cabinet? Any chance this dries and returns to duty?

Steve for Model Number wfw8300sw03

Answer

Was this helpful?

1 Answer

Note: This question is for the older version of this part, but we thought you might still find it helpful

The door on my Duet Sport would not open, upon running diagnostic check got; F-24 water temp sensor, F-01 EEPROM error and F-21 Long Drain, in this order. The water temp sensor tested at 14.3 ohms (aprox. 70 degrees according to chart in service guide, with no water in tub. My assumption was ambient air temp). I cleared the drain filter Which did not have anything substantial clogging it and insured there was no obstructions or kinks in the line. I also tested the water level sensor at 0 ohms while under air pressure. The machine has been on the same power source for 1year now. There are no substantial fluctuations in current and I've had No power interruptions Or surges to point to for the problem. Washer is still not working and still producing the same codes. What should be my next step from here?

Dave for Model Number WFW8300SW03

Answer

Was this helpful?

1 Answer

Note: This question is for the older version of this part, but we thought you might still find it helpful

The "User Interface" flashes really fast with a low tone. It is completely unresponsive. Sometimes it will not light up at all. Any ideas on what went bad?

Cubone for Model Number WFW8300SW05

Answer

Was this helpful?

1 Answer

Note: This question is for the older version of this part, but we thought you might still find it helpful

Hi there. My duet shows a msg of .. f 01 I unpligged all the wiring from ccu and put it back, but didn't fix the problem. Do I really have to order a new ccu unit and will it fix the problem?

Sunny for Model Number wfw8300sw03

Answer

Was this helpful?

1 Answer

Note: This question is for the older version of this part, but we thought you might still find it helpful

I ordered a new control unit (W10246289) for my Duet, and the plastic mountng plate does not match the original. The new one has an 11/2 inch long round tab on the bottom right corner. Because of this I can't fully attache the upper tabs in the key holes o the machine. Can I cut off this tab, and be able to return it needed?

Brian for Model Number WFW8300SW04

Answer

Was this helpful?

1 Answer

Note: This question is for the older version of this part, but we thought you might still find it helpful

The machine has just had a new water pump installed which works fine. The machine has several symptoms.1) The wash or rinse cycle will complete and completely drain and then show a F21code. but only 1 cup of water is left in the drain at the filter. 2) Sometimes the washer will not fill water for a wash or rinse, but it will fill and perform a complete diagnostic cycle up to the spin and then show F21 but there is no water left in the machine because it has all pumped out. 3) The door has to be manually unlocked. The cancel button will only allow 1 press and not 2 to clear the code. I was only able to wash 1 load after installing the new pump. then the trouble began.There was no extra suds, no obstructions in the filter, pump or drain line. The F21 code always shows after all water is out and will not spin.

Alan for Model Number Whirlpool Duet Sport frontloader wfw8410sw00

Answer

Was this helpful?

1 Answer

 

 
 
We are Safe, Secure, Dependable and Trusted
  • BizRate.com Customer Certified Site - Click to Verify