24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Customer Questions and Answers for Control Board by Whirlpool

  1. Our Price $121.25
    Compare At $156.09
    You Save $34.84
     Watch Video
    • Part Number: AP3775585
    • MFG Part Number: 8564547
    • Made by: Whirlpool
    Add to Cart

Questions & Answers

For Whirlpool Control Board (Part Number: AP3775585)

Ask a Question

Most Interesting  |  Latest Questions

Came back from vacation and no lights on key pad Check incoming power, thermal fuse, and both door switches...all ok. Is the problem the electronic control panel? We do get voltage surges here and one of the transistors on the panel looks to have overheated.

Mark for Model Number GU2400XTPB6

Answer

Was this helpful?

1 Answer

My dishwasher fills with water when we first start it. When it is time to wash it shuts down. We resart it and in runs fine.

Anthony for Model Number du1005xtvq1

Answer

Was this helpful?

1 Answer

The pots & pans light blinks, there are two horizontal bars in the time remaining window and the start/resume and the cancel/drain buttons do nothing. You answer this question and said it was a code for the door latch. I replaced the door latch, the door seal and striker and have check the door switches and they are both good. After having the power to the machine off for a couple of days I turned the power back on and was able to get the dishwasher to run until it had about 13 minutes left in the cycle and the same thing happened light blinking, two bars and start button does nothing. I wired around the door switches to make a direct connection and nothing changed. Is it possible something is heating up to cause this problem?

Gary for Model Number GU2400XTPB3

Answer

Was this helpful?

1 Answer

The normal wash light is lit, the pots and pans light blinks and there are two horizontal bars in the time remaining window. Neither the start/resume or cancel/drain buttons do anything.

Gary for Model Number GU2400XTPB3

Answer

Was this helpful?

1 Answer

I have the flashing green clean light issue. Water is hot, element is good. When I go to the normal wash mode, hit start, I hear the water start flowing into the tub. After 20-30 seconds or so I hear a humming noise, not a chatter like a microswitch trying to close but a humming like a coil or something. I am wondering about the overfill switch, water inlet valve, overflow switch lever. Where do you think I should look first?

Jim A. for Model Number 665.17054401

Answer

Was this helpful?

1 Answer

If the Thermo switch opens, will all lights on the front panel remain off? The washer was washing, stopped before drain cycle with all lights off. checked breaker, OK. Reset Breaker, still no lights on. Checked pwr to Circuit board, has pwr, but no lights or switches working. If Control board is changed, the old thermo is placed on the new board. New board installed, no pwr indications. Can a short between the two thermo connectors to see if any light or if any switch works?

David for Model Number 66516012401

Answer

Was this helpful?

1 Answer

I have the blinking clean light problem. Can do the reset and the light goes out sometimes most of the time it will not complete all the cycles and dishes are dirty when it stops. Then sometimes after I do the reset and cancel it does fine like it is supposed to. The element is working because when it completes the cycle and when it's finished and you open the door steam hits you in your face so I would think the element is working? Was thinking about trying a control board, but being they are pricy though I would ask first. I'm fairly handy already opened the front to check connections on the board and door switches all good still has same problem clean light flashing slow wont sratr until you do a reset. My hot Water heater is set at 125 degrees.

Mike W for Model Number GU2400XTPB6

Answer

Was this helpful?

1 Answer

Changed fuse and door switch.Greenlight at "start" blinks when power turned on.Two horizontal lines appear on "Time Remaining".High Temp and Heated Dry hit 4 times turns on all the lights and "88"displays on "Time Remaining"indicator.Pl help to diagnose.Thanks.

Seth for Model Number GU2400XTPS1

Answer

Was this helpful?

1 Answer

The dish washer fills, then cycles down from about 7 minutes, then the LED shows a small L8. This cycles down to a small L3 and stays there perpetually. Then you have to drain it manually to stop it. I have already replaced the panel and control board. My "serviceman" is stumped. Any ideas?

Mike for Model Number GU2400XPT 1

Answer

Was this helpful?

1 Answer

The Start button is not functioning. The other cycle buttons light up but the Start, Delay Start, and Cancel button on the far right side of the contol panel do not work. Not sure if it is the Console Assembly or the Control Assembly that has gone bad????

Jason for Model Number 665.16059402

Answer

Was this helpful?

1 Answer

 

 
 
We are Safe, Secure, Dependable and Trusted
  • BizRate.com Customer Certified Site - Click to Verify