Is there a Dryer Repair Kit for my model dryer? It doesn't appear on the list for the AP3131942 kit.
Answer Mike, the dryer repair kit that you will used on your Kenmore Dryer model 110.66902691 is part number 4392067. Thanks!
Is this the correct kit for model LER7620LGO?
Answer John, according to your model the dryer repair kit 4392065 is the correct kit used on your appliance. Thanks!
ok, i have a maytag neptune washer/dryer set. they are frontload and the dryer is squealing like a banshee, which i assume is a result of the belt pulley being bad because when i shot it with wd-40 it stopped temporarily. the problem is, i cant order the parts without the dryer model number and the sticker has been ripped off (presumably by the previous owner) Is there some way to cross reference my dryer from the washers model number? (maytag neptune washer model #MAH5500BWW) And if not, is there a universal maytag pulley kit that i can order that will work? Thank you for your help.
Answer Hi John. Well then, using the model # MED5500AYW, the dryer tumbler wheel is part # 12001541. The shaft is part # 6-3129480. It is recommended to replace both rollers at the same time. If the blower wheel is rubbing and rumbling loose on the motor shaft, you need to replace it as well. Part # 33002797. The drum belt is part # 33002535. Use the shop vac to super clean all including motor windings and the lint screen housing. Make sure the entire vent system is not clogged and the outside vent hood /cap is opening and closing correctly as to not let the outside rain or dew to re-enter the vent system. This is needed to happen 4-5x /yr so the unit breathes easier and does not overheat the element from red-hot to white hot. Never use WD-40 (or any spray lubricant) in a dryer as it is flammable and will catch the house on fire. Thank You.
Is dryer repair kit AP3131942 compatible with my dryer?
Answer Wendy, the dryer repair kit that you will need to use on your GEW9250PL0 model is part number 4392067. Thanks!
How do I install dryer repair kit? Can I do it myself? How much of dryer do I have to take apart? From back? Dryer is making squeeking noise and then shuts off. Motor still working but must have alot of strain. Noise started a month ago and lst night it just stopped. I tried to restart and smelled motor. It started but stopped again. Look forward to your response..
Answer Brian, A couple of things, This is not a "standard" sized dryer. The dryer repair kit will probably not work on your dryer, and you will need to order the individual parts 3394652 691366 349241T . To access the components you're working with, you'll need to remove the front cabinet and panels of the dryer. First thing, unplug the power cord, or remove power to the unit. 1. Remove the three screws that hold the control panel in place. 2. Remove the transition panel by removing the three retaining screws. The wiring diagram is located on the back side of the transion panel. 3. Lift the console up and flip it forward, being careful not to damage the knobs or the dryer front panel. 4. Using a putty knif, release the two reatining clips and remove the toe panel. 5. Disconnect the door switch wires. 6. Remove the control panel from the front panel and set it on top of the unit. 7. Remove the top two retaining screws. 8. Remove the bottom two screws. 9. Remove the lint screen. 10. Remove the three dryer lint duct assembly retaining screws and remove the assembly. 11. Remove the four heater element shield screws. 12. The dryer front panel can now be removed. Remove the blower assembly,transition duct and blower plate by removing the retaining screws. 13. Using a ratchet wrench and extension to hold the drive motor shaft stationary, remove the blower wheeel. You can now remove the belt, and tumbler to access the rollers, motor and idler assembly. Thanks and Good Luck
Will this kit fit my unit?
Answer Hello Frank. Yes, based on the model number, 4392065 is the correct kit. Hope this helps.