24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Customer Questions and Answers for Electronic Control Board by Whirlpool

  1. Our Price $181.89
    Compare At $216.45
    You Save $34.56
     Watch Video
    • Part Number: AP3775506
    • MFG Part Number: 8564543
    • Made by: Whirlpool
    Add to Cart

Questions & Answers

For Whirlpool Electronic Control Board (Part Number: AP3775506)

Ask a Question

Most Interesting  |  Latest Questions

Note: This question is for the older version of this part, but we thought you might still find it helpful

The display shows 2 dashes and the "normal" and "rinse only" lights are blinking (no other lights illuminate). The reset code Hi Temp Scrub, Energy Saver Dry, Hi Temp Scrub, Energy Saver Dry does not turn on any other indicators. I have bypassed the door latch switch(jumper) and I have bypassed the fuse(jumper) to no avail. Also I have checked the ribbon connections and everything is clean and well connected. Do you think this is this the control board or the touch Panel? How do I know if the machine in "standby"? Thanks!!! JS

Jody for Model Number kudso1ilbs6

Answer

1 person found this answer helpful.

Was this helpful?

1 Answer

Note: This question is for the older version of this part, but we thought you might still find it helpful

All lights on control panel light up when pressed to select desired schedule. Problem is when the start button is pressed nothing happens. No sounds or anything. The unit then shuts off the selected lights. Problem appears to be in the start of control. Does the control panel include switch located under the buttons? If I order the control panel is all the necessary parts included?

Mr, B for Model Number Kudso1flwh6

Answer

1 person found this answer helpful.

Was this helpful?

1 Answer

I've got a whirlpool "Quiet Partner II" dishwasher, it's about 2 yrs. old and it quit working mid cycle and now there is no power at any and all of the push bottoms, no lights, no nothing. I checked power at the plug...it's good and have power at the junction box on the dishwasher itself. Any ideas?.....control board maybe? Thanks much in advance for you help

Paul for Model Number DU1055XTVQA

Answer

Was this helpful?

1 Answer

DW does not turn on when START button is pressed. I checked all of the buttons by turning on the control lock and pressing each button - they all cause the lock LED to flash. I ran the diagnostic test (pressing Hi Temp Scrub, Energy Saver Dry, Hi Temp Scrub, Energy Saver Dry) and all of the cycles ran perfectly. Do I need a new control board?

Joe for Model Number kudio1il bl1

Answer

Was this helpful?

1 Answer

Green light on front of dishwasher blinking 7 times and dishwasher shuts down. I ordered replacement heating element and control board but when I opened the door panel I noticed that some of the wiring looked burned and the insulation on the door had melted in those areas. The original control board part number is 8564546. The new part number that came with the heating element kit is 8564543. Two questions: Is the new part number correct? Will replacing the control panel eliminate the burning wire issue?

Swtsgg for Model Number Kenmore Elite Dishwasher

Answer

Was this helpful?

1 Answer

My dishwasher will not drain. The motor does not seem to even try to start. I removed the motor and bench-tested. Seems to work fine. The drain cycle worked a few times when I manually executed a "cancel/drain", but this is now no longer working. I assume there is a relay that kicks-in the motor. Is the relay replaceable? Where is it located? Thanks!

Bob R for Model Number kudm01tjbl0

Answer

Was this helpful?

1 Answer

When I started my dishwasher the start/resume button turned on as usual then after a few seconds the start/resume button started flashing. The washer seems to fill up with a small amount of water and luckily when I press the cancel button it drains. We have tried to reset the panel twice. Normal heat dry normal heat dry. Then it acts like it wants to run because it stays in wash mode..... nothing happens but we can here a faint clicking sound coming from the panel after the reset.

Cally M for Model Number KUDS03CTSS3

Answer

Was this helpful?

1 Answer

Cancel button works, pump runs to drain water. All of the lights on the control light up when pressed. I pick the cycle I want, normal, energy save, and press start and nothing happens. With in a minute the lights go out. Control panel problem?

Al R for Model Number kudio1il

Answer

Was this helpful?

1 Answer

Hello! My problem is that the heating element is broken but the dishwasher works. I read on some websites that if I change the element I also have to change the control board. I would like to know if it is true and what is the reason to do so. Thank you very much. Jean-Pierre Pelland majelo9@hotmail.com

Jean-Pierre P. for Model Number Kenmore 665.16389300

Answer

Was this helpful?

1 Answer

My unit has pwr. To it, but the control panel w/n work properly causing the unit not to work. When i unplug & replug the 120 vac cord to reset it, the normal & rinse cycle led's come on & the no. 2 is displayed in the window. I do here the drain pump working for a short while then it stops. After that happens the normal & rinse cycle led's start flashing & the time remaining window has 2 green steady "on" dashes. No other buttons on the control panel light-up when pressed. I do notice the anti-bacterial & pots/pans buttons do not have that spring back feel to them like the other buttons do on the c/p.

Ron B for Model Number GU1500XTLS2

Answer

Was this helpful?

1 Answer

 

 
 
We are Safe, Secure, Dependable and Trusted
  • BizRate.com Customer Certified Site - Click to Verify