24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Customer Questions and Answers for Element, Surface by Whirlpool

  1. Our Price $99.58
    Compare At $128.04
    You Save $28.46
     
    • Part Number: AP3842098
    • MFG Part Number: 4453909
    • Made by: Whirlpool
    Add to Cart

Questions & Answers

For Whirlpool Element, Surface (Part Number: AP3842098)

Ask a Question

Most Interesting  |  Latest Questions

When facing the stove, I have a problem with the large front right burner. Only the center part of the element turns on even when I turn it all the way up. Thanks.

Craig for Model Number MER5770BAW

Answer

Was this helpful?

1 Answer

What is the part number for the rear right burner for the GJC3034HB4 cook top?

Garry for Model Number whirlpool gjc3034hb4

Answer

Was this helpful?

2 Answers

What is the part number for the rear right burner for the GJC3034HB4 cook top?

Garry for Model Number whirlpool gjc3034hb4

Answer

Was this helpful?

2 Answers

Whirlpool Electric Range, Temperature Problem(Dual Zone) When I set at low temperature, then elements are on HIGH HEAT (Red Burn Color). What parts do I change ?

Moon for Model Number GR475LLS1

Answer

Was this helpful?

1 Answer

Front dual burner heats up to point of glass being red at any setting.

Charles for Model Number rf367lxsy0

Answer

Was this helpful?

1 Answer

Left front dual burner . Only outer segment heats. Center one does not.

Bruno for Model Number GLP84800

Answer

Was this helpful?

1 Answer

Note: This question is for the older version of this part, but we thought you might still find it helpful

I just purchase this element for my front burner on my Jenn Air, and it does not match what I pulled out. My old radiant element has an additional black prong on it.......it is a double element..... Do I need a different element....?

Claire for Model Number clalem2005@yahoo.com

Answer

Was this helpful?

1 Answer

My dual element only comes on full blast on both elements no matter where the selector is... inner or both. What do I need to replace? Thanks!

Mike for Model Number kerc507hal0

Answer

Was this helpful?

1 Answer

Note: This question is for the older version of this part, but we thought you might still find it helpful

Jenn Air Elec Range, Dual Element Not Working --------------------------------------------- I hope you can help me. The left/front surface element of our Jenn-Air electric range (Model No.: JER8885RAF, Serial No.: 1239660LF) does not turn on but the "element on" LED lights up when the switch/knob is turned in either direction. This element is controlled by the left most switch and the burner is a "Dual Ultra High/Low" surface element. I ordered a replacement surface element (7406P403-60) and switch (74010824) from AppliancePartsPros.com and received what looked like the incorrect parts. My surface element has a sensor in the element and a black wire with a wire harness connector. The element infinity switch is black (not white) with two (2) rectangular cable connectors plugged into the switch. The top plug has 6 wires (orange, tan black, black, blue, yellow) and the bottom plug has two wires (red/red) connected to the first position and two wires (black/black) connect to the last position. Looking from the back, my orientation is left to right. After I removed the glass top surface from the range and before I noticed that I had the wrong parts, I made some resistance readings on the original element. The internal element windings seem to connect to three (3) pins on the outside of the surface next to the input electrical connector. If I call the 3 pins A B and C, where A and B have connected wires and C is connected to the input electrical connector. The sequence is A, B, C, and then the input connector. The resistance readings I obtained were: A to B: 68 Ohms B to C: 37 Ohms A to C: 32 Ohms where A B and C represent the left, middle, and right terminals of the surface element. Also, looking at the nine (9) pin harness connector from the range top, one of the pins on the pins seems to be dis-colored. This pin is in the upper right position and is bare where all the other pins are in a plastic sleeve. The pin doesn't smell burnt and I was able to get connectivity between the connector and the surface element. I was not able to check the other end. I did not take any resistance readings at the infinity switch. Do you think my problem is the switch, element, or something else? Hopefully, you can help me trouble-shoot this problem.

Sdl for Model Number JER8885RAF

Answer

Was this helpful?

1 Answer

Please tell me how to insert this plate.

Ann for Model Number 4453909

Answer

Was this helpful?

1 Answer

 

 
 
We are Safe, Secure, Dependable and Trusted
  • BizRate.com Customer Certified Site - Click to Verify