24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Customer Questions and Answers for Filter by Whirlpool

  1. Our Price $32.10
    Compare At $38.93
    You Save $6.83
     
    • Part Number: AP5631266
    • MFG Part Number: W10367632
    • Made by: Whirlpool
    Add to Cart

Questions & Answers

For Whirlpool Filter (Part Number: AP5631266)

Ask a Question

Most Interesting  |  Latest Questions

I can build racing engines but apparently, I am not capable of fixing a Maytag Washer. Here is what happened so far: The washer stopped working properly and had an F31 Error Code. I called a Sears technician who diagnosed: F31 Error/Locked/Not spinning correctly. Status: Needs Motor Board. He wanted $500 to replace that part but tried to push me into buying a new washer and even offered me a 10% coupon. I declined his offer. In the mean time, I ordered a Motor Control Board (different source), replaced it but other than that the F31 Code disappeared, the washer is still not working and had a F26 Error (door Switch). Then I found your AWESOME website and found cool diagrams and ordered parts. I ordered and replaced the door latch and the upper control unit (AP5787744). NOTHING has changed :/ Today's situation: 1.) Door locks but only unlocks by manually pulling the latch 2.) I can dial in any wash program and start it. The detergent mechanism moves, the water fills up, Drum DOES NOT SPIN, the water drains out, the timer will count down to like 3 mins. and then all the controls are blocked until I pull the power and plug it back in. 3.) When ever I hit Stop/Cancel at anytime, the controls block until I dis/reconnect the power cord. 4.) I can get/read error codes but I can not start the self diagnose test. If I try, it goes into Test mode but freezes (or am I supposed to patiently wait while it does not appear to do anything?) I checked the belt and the motor, the whole assembly turns smooth (pulley/belt/drum) when turned by hand. Maybe one of the parts I ordered was defective? I am out of ideas and would appreciate your input VERY MUCH :) Regards, Moe

Frustrated Moe for Model Number Maytag Epic Z MHWZ600TW01

Answer

Was this helpful?

1 Answer

Washer has been working through all cycles, but it seems to buzz at times. I haven't checked during exactly what cycles it buzzes though. I assumed it was the draining part because it comes and goes. I live in the country and get my water from a well and had sediment earlier this year with my drinking water and never thought about the washer... I took one of the hoses off and a little chuck of sediment fell out. Im going to check to see if any thing is in the drain pump and if there is a screen or filter. Is there any thing else I should check out? Thank you

Michael St George for Model Number WFW9050XW00

Answer

Was this helpful?

1 Answer

Unit doesn't drain or spin, smelt a burning odor.

Bruce for Model Number Wfw8300sw04

Answer

Was this helpful?

1 Answer

Washer quit working again. It filled with water and stayed dead. No agitation action, no spin. Lid switch is good ! Found burnt surrounding area where the power filter is mounted. I just replaced this filter couple of months ago. Also have two more of the similar model were burnt spot in the area of the filter. What is going on here ? What else should i check or part to buy ? help here pls...

Troy for Model Number wtw57esvwo

Answer

Was this helpful?

1 Answer

Washer stopped working after filled....completely dead. Opened the control panel and found filter and surrounding area sign of burnt. Could it be the filter ? what is the main purpose of this part ? Can i remove the filter from the circuit and re attach the harnessess (basically by-passing it) to see if the unit will run and conclude that it's the filter ? Just for testing purposes ? Will it explode if i do that ? Kindly advice and thanks

Troy for Model Number wtw57esvwd

Answer

Was this helpful?

1 Answer

Note: This question is for the older version of this part, but we thought you might still find it helpful

I am replacing the filter part no. ap5271032 and I dont remember of the two plug wires where they go, one is light grey and the other is light grey with black stripe, the filter shows one pugs into "L" and one plugs into "N" which one is L and N ?

Nelson for Model Number wtw57esvw0

Answer

Was this helpful?

1 Answer

Note: This question is for the older version of this part, but we thought you might still find it helpful

I just replaced the CCU. After testing the door look assembly by ohming out the pins on the connector at plug 6, connector number five counting from the right side of the CCU. I got a reading of 120 for pins 1 and 3 and 60 for pins 2 and 3. This means the door locking /unlocking coils are good does it not? I still get the door locking relay trying 'six' times to lock the door and then the 'beep' and Fdl code? I have tried unplugging the machine for thirty plus minutes in an attempt to get the CCU to reset to factory codes to no avail. I have just checked the line interference filter and it appears good also, 125 volts in and 125 volts out. A few more components purchased and I will have spent enough to buy a new front loading washer off of the appliance showroom floor. I know it could be a bad replacement CCU I haven't ruled that out but would rather not think that just yet, it's got a 1 yr warranty on it and is just a day old at this point. If I purchase a new door lock assembly, it's a shot in the dark, and I will have become the notorious parts swapper. I hated those guys instead of doing the standard diagnostic procedure these guys would replace this component, then that component, until eventually they would finally stumble on to the 'bad' component and restore operability of the machine. One thing that bothers me is initially when I removed the old CCU and hooked up all the connectors I was then ready to 'energize' the machine. I plugged it in and, well, did not hear the slight audible ‘click’ associated with the CCU powering up? Bad power relay on the board? I do have power out through the selector switch and the settings led push buttons, but it never gets past the Fdl code. So... what do you guys think? Any suggestions?

Joel for Model Number GHW9400PWO

Answer

Was this helpful?

1 Answer

Note: This question is for the older version of this part, but we thought you might still find it helpful

My washer stopped working an had a burn smell so i replaced the motor . I started the washer it filled w/water but would not wash when i moved the timer it would spin an drain . is it a bad new motor?

Lee for Model Number wtw57esvwo

Answer

Was this helpful?

1 Answer

Note: This question is for the older version of this part, but we thought you might still find it helpful

O.K. I have been very lucky fixing all Duet problems with your help. I have no power after line filter. No read on meter unless I am doing something wrong. No lights on front panel, No clicks or noise from washer at all. Power at wall. Can this filter completely stop power?

John C. for Model Number GHW9200LW

Answer

Was this helpful?

1 Answer

Note: This question is for the older version of this part, but we thought you might still find it helpful

machine stopped working completely, no sounds, no lights, no clicks...I changed the filter (Electrical - Part AP5271032)and still, no sounds, lights... nothing. would the next part to change be the Microcomputer,Machine Control(Part W10161727)?

Mm for Model Number WFW9200SQA12, duet ht

Answer

Was this helpful?

1 Answer

 

 
 
We are Safe, Secure, Dependable and Trusted
  • BizRate.com Customer Certified Site - Click to Verify