I need to replace the oven door hinges. Your diagram shows two different P/N's, 7 P/N 74011141 and a &A P/N 7106P045-60 with a $10 difference. Which part do I need to order or do I have to remove the old hing and try to match visially? Also, I'm guessing the hinges are easily replaced by removing only the door, hinge retaining screw and then wiggle the old hing through the rectangular hole. I'm I close?
Answer Hello Ohbob,
The difference in the parts is based off serial number. If you have serial number 10-16 as first 2 digits then you would use part number [APAP4089688]. If you have Serial number starting with 17 or higher you will use part number 74011141. To remove the hinges you will have to lift door off the hinges by opening door til it reaches first stopping point. Once at this point lift straight up and off. You will have to pull unit out of wall a little to remove the hinges from the side after removing screws.
Can you tell me how I can remove and install new hinges on my oven door?
Answer Hello Ljubica. Remove the range top and remove the 7 phillips screws from either rear edge that secures the side panels to the back of the range. Remove 3 screws from the top edge of the side panels on this gas model and pull upward and remove thr side panel. Now you can access and replace the door hinge 74011141 on the unit. Hope this helps.
Door hinges are broken on our Maytag oven( model MGR5750ADW). What steps do I need to take to replace them? Thanks
Answer Hello Lisa. You will need to raise the top of the unit and remove the back and side panels to access and replace the hinges. The door lifts off the unit to replace the hinges 74011141. You will need to door to be at the first stopping point to lift it off the unit. Hope this helps.
2nd Request...I purchased 2 hinge assemblies for Model MGR5250ADW....Are there any easy steps to install these hinges? Does the inner oven housing have to come out? The oven door is off..HELP please
Answer Hello Anthony. Remove the door from the oven. Then remove the screws securing the hinges. Once removed, you will tilt the hinges 74011141 and work them out of the body of the range. Reinstall in reverse order. Hope this helps.
I want to replace both hinge assemblies.can I buy a LEFT and RIGHT assembly and does the entire oven interior have to be removed to replace the hinge assemblies? Also is the hinge mounting screw or bolt come with the assembly?
Answer Anthony, Both the hinges are the same, so you will need to order 2 74011141 , not a left and right hinge. First, remove power to the range. You will need to remove the oven door, Open the door to the broil stop grasp the door on both sides and lift up and slide the door off the hinge assembly. You will then need to remove the cooktop burners(label the burner location first, twist the burner 90 dgs. counterclockwise and raise up on the burner, label and disconnect the igniter wires. Remove the two phillips head screws holding the burner bracket to the underside of the cooktop, then lift up on the front corner(s) of the cooktop and raise and remove the cooktop. Remove the three screws holding the side panel to the frame and lift up on the side panel until the "key hole" retainer disengages from the bottom of the frame, and set the side panel aside. You will have access to the hinge, remove the hex head screws from the front flnge of the oven and remove the hinge. Thanks and Good Luck
Is the part #AP4101300, Oven door hinge, the same one for both the right and left? It looks the same as the one that I removed.
Answer Hello Richard! Yes, the oven door hinge part number 74011141 can be used as the left or right hand side hinge for the oven door. Thanks!
Only half the question was answered, how do I access the hinges?
Answer Hello Lowell. Remove the door from the oven. Then remove the screws securing the hinges. Once removed, you will tilt the hinges 74011141 and work them out of the body of the range. Reinstall in reverse order. Hope this helps.
I have noisey hinges when the oven heats up. Can they be lubricated, and how do you get at them to lubricate or replace? Instructions for another model posted don't seem to apply.
Answer Hello Lowell. Yes, you can lubricate the hinges with high temperature grease TJ17001004. You will need to remove the hinges from the oven and put it on the rollers and spring hooks. Also any joints will need to be greased as well. Hope this helps.
How can I replace the oven door hinge? I bought one from this site, it looks exactly like the one on the right side of the oven. There is no way to get the new one into the left side slot ? And get the old left side out ? Is this
an in shop only repair?
Answer Hello C. Jones. Here are the instructions from the manufacture. Hope this helps.
1. Open the door to the stop position.
2. Lift the door up and off the hinges.
3. Remove the two 5/16 screws holding the hinge to the frame.
4. Pull the hinge forward through the opening of the frame.