How do I replace the oven door hinge on this range? Part number is AP4101300.
Answer Hello Greg. To get to the oven door hinges, you will need to remove the main top, the door assembly, and the side panel. To remove the main top you will need to take the screws out from the door opening... more on either side panel. Once the screws are out, you will need to then disconnect the harness at the back of the main top and set to the side. Remove the oven door by opening the door at a 45 degrees and lift the door off. You will then remove the screws from the top and back that hold the side panel in place.
Is part number # 74011141 door hinge correct for both the right and left door hinge?
Answer Hello Dennis! Yes, the oven door hinge 74011141 can be used as the left or right hand side hinge. Thanks!
How do I get to the oven door hinge to replce the sring?
To get to the oven door hinges, you will need to remove the main top, the door assembly, and the side panel. To remove the main top you will need to take the screws out from the door opening on either side panel. Once the screws are out, you will need to then disconnect the harness at the back of the main top and set to the side. Remove the oven door by opening the door at a 45 degrees and lift the door off. You will then remove the screws from the top and back that hold the side panel in place.
Will part number AP4101300 fit in my oven? I dont know part number on my door bracket.
Answer Hello Jose! No, the oven door hinge 74011141 is not listed for your GE model JTP45B0A1BB. According to your model the right hinge assembly is part number WB14T10005 and the left hinge assembly is part number WB14T10006. Thanks!
Is this replacement hinge threaded for a screw or is the screw a self-tapping screw? I don't want to attempt to use the existing screws only to find that I've cross-threaded the new hinge.
Answer Mike, The hinge screws are "self tapping" and will create threads as the screw is driven into the hinge. You may find it a lot easier, if you partially drive the screw into the hinge mounting holes (4 or 5 revolutions), remove it and install the hinge and drive the mounting screw all the way.
I need to replace the oven door hinges. Your diagram shows two different P/N's, 7 P/N 74011141 and a &A P/N 7106P045-60 with a $10 difference. Which part do I need to order or do I have to remove the old hing and try to match visially? Also, I'm guessing the hinges are easily replaced by removing only the door, hinge retaining screw and then wiggle the old hing through the rectangular hole. I'm I close?
Answer Hello Ohbob,
The difference in the parts is based off serial number. If you have serial number 10-16 as first 2 digits then you would use part number [APAP4089688]. If you have Serial number starting with 17 or higher you will use part number 74011141. To remove the hinges you will have to lift door off the hinges by opening door til it reaches first stopping point. Once at this point lift straight up and off. You will have to pull unit out of wall a little to remove the hinges from the side after removing screws.
Can you tell me how I can remove and install new hinges on my oven door?
Answer Hello Ljubica. Remove the range top and remove the 7 phillips screws from either rear edge that secures the side panels to the back of the range. Remove 3 screws from the top edge of the side panels on this gas model and pull upward and remove thr side panel. Now you can access and replace the door hinge 74011141 on the unit. Hope this helps.
Door hinges are broken on our Maytag oven( model MGR5750ADW). What steps do I need to take to replace them? Thanks
Answer Hello Lisa. You will need to raise the top of the unit and remove the back and side panels to access and replace the hinges. The door lifts off the unit to replace the hinges 74011141. You will need to door to be at the first stopping point to lift it off the unit. Hope this helps.
2nd Request...I purchased 2 hinge assemblies for Model MGR5250ADW....Are there any easy steps to install these hinges? Does the inner oven housing have to come out? The oven door is off..HELP please
Answer Hello Anthony. Remove the door from the oven. Then remove the screws securing the hinges. Once removed, you will tilt the hinges 74011141 and work them out of the body of the range. Reinstall in reverse order. Hope this helps.