24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Customer Questions and Answers for Icemaker, Complete Add on Kit. by Whirlpool

  1. Our Price $81.83
    Compare At $111.74
    You Save $29.91
     Watch Video
    • Part Number: AP3062348
    • MFG Part Number: 1129316
    • Made by: Whirlpool
    Add to Cart

Questions & Answers

For Whirlpool Icemaker, Complete Add on Kit. (Part Number: AP3062348)

Ask a Question

Most Interesting  |  Latest Questions

Need ice maker, does this mod # have a flat male harness connector?

Loiver B. for Model Number ap3062348

Answer

Was this helpful?

1 Answer

Would this kit fit in my refrigerator? I couldn't find it in the list below. Mahalo.

Ron for Model Number ED25QXDW03

Answer

Was this helpful?

1 Answer

Does Kenmore make a replacement ice maker that makes different size ice? If so, Will it fit my older refrigerator?

R.w. for Model Number 106-57372700

Answer

Was this helpful?

1 Answer

Looking for an Add on Ice maker- production date is 4-96 Thank you in advance if you can get me the right one.

Todd for Model Number ET20TKXDN03

Answer

Was this helpful?

1 Answer

Our less than 2 year old icemaker has stopped making ice. A while back it was making a lot of noise, but returned to normal later. It has been erratic, sometimes making very little ice and doing well at other times. It has now stopped making ice altogether. The water supply is fine with no obstructions. While checking the bottom of the icemaker I got a nasty burn, so I concluded that the heater must have been stuck in the on position. I have removed the unit and found the tray about half full and the "ejector blades" firmly frozen in the ice and pointing straight down. This has to be wrong. The dial that controls the "ejector blades" must have a specific starting position, but I find that I can insert the knob into any location on the gear. What is the correct position and how do I check to determine if the motor is shot or if there is another issue?

Skip for Model Number ECKMF90 KIMS8

Answer

Was this helpful?

1 Answer

Is there a complete icemaker add on kit for the kenmore listed above.... thanks

Erin for Model Number kenmore 1069545711

Answer

Was this helpful?

1 Answer

My parents have a Whirlpool model ET1FTKXKQ02 that did not come with an ice maker. I would like to get them an icemaker and install it in this fridge/ freezer. It has freezer on top fridge on bottom. It has no fancy door stuff for ice or water it's pretty much a plain fridge freezer. It has a spot in the back top left of the freezer that has a cover on it. What model ice maker would fit in this freezer. All I can find is replacement kits but I need a complete kit.

Xab for Model Number Whirlpool model ET1FTKXKQ02. MFG date 02-03

Answer

Was this helpful?

1 Answer

I would like to put an ice maker in my kenmore, what complete kit will work?

Robert for Model Number 106.63182302

Answer

Was this helpful?

1 Answer

My ice maker drips slightly when making ice. I hear the solenoid opening/closing normally but as it makes ice, water drips in with the cubes very slowly and continuously. I have to believe the water is dripping past the valve, but I'm not sure as the ice cubes are full size. Would you recommend replacing the valve first and if so what part number? (It was manufactured in 08/99 and have the ice maker water shut off for over a year and bar raised on the maker so it hasn't been running dry). Thanks, Greg

Greg for Model Number KitchenAid KTRS22KHWH00

Answer

Was this helpful?

1 Answer

Actually folks, you didn't read my entire previous question. If you had, you would have answered my question about the lack of 2 sepearate leads at the right rear bottom of the unit, where the water valve would go. There are no extra leads to which I would connect the water valve you provided in the kit. You should scrutinize the questions sent to you better as to not waste undue time. I did as you asked with the wire harnes and disconnected the one that came on the ice maker. When I did so, I took another look at the exisitng harness inside the freezer and noticed an additional plug (adapter) hooked to the end of the harness. When I removed that adapter, it revealed the correct connector that would indeed fit the small harness that came attached to the ice maker. So, that then is no problem. I have only the water valve problem to solve and I can get to work installing the ice maker.

Lee T. for Model Number KTRS20KAWH10

Answer

Was this helpful?

1 Answer

 

 
 
We are Safe, Secure, Dependable and Trusted
  • BizRate.com Customer Certified Site - Click to Verify