24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Customer Questions and Answers for Motor Control Assemb by Whirlpool

  1. Our Price $209.05
    Compare At $248.77
    You Save $39.72
     
    • Part Number: AP4027228
    • MFG Part Number: 22004046
    • Made by: Whirlpool
    Add to Cart

Questions & Answers

For Whirlpool Motor Control Assemb (Part Number: AP4027228)

Ask a Question

Most Interesting  |  Latest Questions

Ordered the replacement motor control assembly listed on your site for my Maytag Neptune washer - MN MAH4000AWW. A appliance repair company tech reported that the existing assembly was kaput. The assembly I received doesn't even come close to matching the existing assembly. Apparently, there is a wiring harness needed to hook up the new assembly to the existing motor but that was not noted in the replacement part listing. So, even though the parts matching link says the assembly works for my washer, it really doesn't without the missing wiring harness. I don't want to buy a new motor since the existing one works fine but it looks like that is what you are advocating. This has turned into a big inconvenience for me along with a wasted hour trying to make sense of the mismatch. Do I need the wiring harness? Will this motor control really work with the existing motor or will I have to purchase that as well before I get anywhere near success with this replacement? What would I have heard from the appliance repair shop if I had agreed to have them fix the stupid thing?

Captain Bligh for Model Number MAH4000AWW

Answer

Was this helpful?

1 Answer

washer will shut off during rinse cycle. press start button and washer starts up. will shut off again during spin cycle, press start and washer finishes cycle. door lock light does come on. have run washer with no clothes in it and washer runs through complete cycle.

Joe for Model Number MLE2000AYW

Answer

Was this helpful?

1 Answer

Hi guys - what an excellent site! Can you ship parts to the UK? Or do you have an outlet over here? - Regards Steve

Steve B. for Model Number MAH14PNBGW

Answer

Was this helpful?

1 Answer

Neptune washer doesn't enter high speed spin. Does this mean that I must replace replace the motor control board or are there other possible causes?

Dick for Model Number MAH3000AWW

Answer

Was this helpful?

1 Answer

Motor control part #22004046. Testing following the Drive System Phase Loss Test shows that one phase is bad. Do you have a board level schematic that would show the component parts. I would like to replace the defective component parts rather than the whole board.

Al for Model Number MAH4000AWW Maytag Washer

Answer

Was this helpful?

1 Answer

Will this part (#AP4027228 Motor Control Bd.) fit the series 14 washer.

Wayne for Model Number MAH21PDAWW

Answer

Was this helpful?

1 Answer

Maytag Neptune washer with LR error code after wash cycle but without spinning and before rinse cycle. Went through diagnostics and the Spin test shows that the basket will spin at the different levels of test up 99. Quick Cycle test also shows that each stage of the complete wash cycle is working. I can force a spin and a rinse cycle but the basket doesn't spin as fast as it should and clothes are much too wet after. Water is draining, hose was cleaned. Door is locked. Essentially no spin and machine times out with LR code. Also, motor load test does not respond while in service mode. Is this a motor control board issue? Thanks!

Clay for Model Number MAH5500BWW Ser#B7103557GT

Answer

Was this helpful?

1 Answer

I have a Maytag Neptune and it start making noise when it turns one way or the other. Noise is at lower movements with turning or spinning and clothes still very wet. Took off the belt to the drum and I still hear the noise so it's not the drum bearings. The motor shaft spins freely by hand turning with no noise or friction. The noise is just when it kick on and when it kicks off the shaft still spins for sometime without the noise. Could it be the control motor or is it still the motor. Again the washer drum also spins freely without noise when I have the belt off the back wheel of the drum. Motor P/N 62 702230 Model H55BMBJL-1820.

Rich B for Model Number MAH4000AWQ serial #40378222WH

Answer

Was this helpful?

1 Answer

Neptune washer does not go into high speed spin at spin cycle. Water pumps out fine. Tumbles left and right several times and then ends spin cycle. Door locks. Door wax motor replaced a few years ago, control board has no burnt components (replaced with wax motor). Removing connector JP4 and testing allows drum to spin at 50 rpm. Jumped unbalance switch but it still doesn't spin out. Voltage across tub displacement switches is within what I was told is an acceptable range. Tried running diagnostics included with schematic. Seem to have the newer motor/motor control board. Doesn't have the individual wires to disconnect to test each phase as detailed in diagnostics. Hate to buy motor control board if that's not the problem. Any other checks, or does it look like the motor control board? Thanks

Todd for Model Number MAH4000AWW

Answer

Was this helpful?

1 Answer

Door lock light not lit and spin cycle not working. Everything else seems to function fine. Is it the wax motor?

Ron L for Model Number MAH4000AWW

Answer

Was this helpful?

1 Answer

 

 
 
We are Safe, Secure, Dependable and Trusted
  • BizRate.com Customer Certified Site - Click to Verify