MCU # 8182706 has a fried resistor at R6SP on back of board. What is the part # or the ohm value for the resistor.
Unfortunately we do not have information on individual components of the control board as the manufacturer does not provide this information.
I had a F21 code then a F28 code.
Answer Hello Ben,
The F21 is the code for a long drain. For this code you need to check the pump area for debris and check the pump for normal operation. As per the tech sheet: If the drain time exceeds eight minutes, “F21” will be displayed, the water valves will turn off and the pump will stop running. Press PAUSE/CANCEL to drain the machine. The display will be cleared and the machine will turn off after a maximum of eight
minutes. Possible Causes/Procedure - 1. Check the drain hose and make sure it is not plugged or kinked. 2. Unplug washer or disconnect power. 3. Check the electrical connections at the pump and make sure the pump is running. 4. Check the drain pump filter for foreign objects. 5. Plug in washer or reconnect power. 6. Unplug washer or disconnect power. 8. Replace the pump.
The F28 is a serial communication error. The tech sheet instructs the following for this code: The communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly. Possible Causes/Procedure 1. Unplug washer or disconnect power. 2. Check wire harness connections to the MCU, the motor, and Central Control Unit (CCU). Check connections of the CCU board within the housing. Make sure all grounding switches are engaged. 3. Check the drive system for any worn or failed components. 4. Plug in washer or reconnect power. 5. Verify CCU operation by running a Diagnostic Test or any cycle. 6. Check the MCU by looking for operations of the drive motor. 7. Check the drive motor for powered rotations. 8. Check that the serial harness at the MCU is not mounted upside down. The wires should be to the left when facing the MCU connectors.
Kenmore HE4t. history of F11 error code on spin cycle usually. i ordered this replacement CCU and installed it. now i get the error code (F11) right away just as the cycle starts to work.
Answer Hello John. The Motor Control Unit has internal failure. If failure occurs during high-speed spin the
door unlocks after 3 minutes. This error code is only shown in Diagnostic test. Possible Causes/Procedure
- Verify the shipping system including shipping bolts and spacers are removed,
and power cord out of the unit.
- Check if washer is on a dedicated circuit. Other devices on same circuit can create
line noise and cause this issue.
- Unplug washer or disconnect power
- Check the neutral feed to the MCU and CCU from the AC line filter.
- Check all wire harness connections between the Motor & MCU, and MCU to CCU,
are not broken or wires detached and connector internal pins are visible.
- Make sure that all the connectors are fully seated.
- Plug in washer or reconnect power cord.
- Verify the unit operation by running the Diagnostic Test cycle. See page 5.
- After the diagnostic test has finished, unplug washer or disconnect power cord
and wait for 15 seconds.
I am getting F06 and want to perform the resistance checks. It's not clear to me what needs to be disconnected and exactly where the test points 1,2 & 3 are located. Do you have a video for this or more detailed instructions? The wiring connectors all seem to be snapped in place so I suspect it is a failed MCU. I have read that the fuse on that board can be the culprit but it is not replaceable. Is there a check for that?
Answer Hello Paul,
As per the tech sheet: This is a drive motor tachometer error. The control is unable to properly detect motor speed and the machine will shut down. If a failure occurs during high-speed spin, the door will be unlocked after three minutes.
Possible Causes / Procedure
1. Verify the shipping system including shipping bolts, spacers and cables are removed.
2. Unplug washer or disconnect power.
3. Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU).
4. Plug in washer or reconnect power.
5. Check the MCU by looking for operations of the drive motor.
6. Check the drive motor for powered rotations.
If you refer to page 13 of the tech sheet, the top left part of the wiring diagram, you will see the terminals labeled GND, In/Out, and Vcc. If there is a fuse on the board, you can check that with an ohm meter. If it is submerged in an epoxy type substance, the board will have to be replaced.
I've been getting 2 different error codes. One is an F1 E2 and the other is an F6 E2. I get the F1E2 more often. I've cycled the power and checked all of the connections that I can. Do you think it is the CCU or the MCU? If I by one and it doesn't work, can I return it to get the other?
The F1 E2 error is a MCU Error with multiple resets. Motor Control Unit (MCU) has an internal malfunction, repeating under or over voltage, or over current conditions. Can also be caused by momentary loss of neutral feed to MCU during the spin cycle. If the error occurs during a high-speed spin, the door will remain locked for 3 minutes.
TEST #3: Motor Circuit
This test checks the motor, motor control unit (MCU), and wiring. IMPORTANT: A guide (W10271535) is required to assemble the rotor onto the shaft. The guide is inserted into the threaded hole, and then the rotor is slid on over the guide.
NOTE: If the harness between the CCU and MCU is removed or communications are interrupted during operation, the MCU puts the motor into a braking mode, resulting in a significant drag on the drum when turned by hand. This mode can be cleared by removing power from the washer for a few seconds.
1. Check the motor and electrical connections by performing the “Quick Diagnostic Test” on page 6. The following steps assume that this
step was unsuccessful.
2. Unplug washer or disconnect power.
3. Check to see if basket will turn freely. If basket turns freely, go to step 4. If basket does not turn freely, determine what is causing the mechanical friction or lockup.
4. Remove the top and rear panels to access the machine electronics and motor components.
5. Visually check that connectors MS2 and MI3 are inserted all the way into the CCU. If visual checks pass, go to step 6. If visual checks fail, reconnect MS2 and MI3, and repeat step 1.
6. Visually check that all connectors are inserted all the way into the MCU (see Figure 6, at left). If visual checks pass, go to step 7. If visual checks fail, reconnect the MCU connectors and repeat step 1.
7. Check the motor windings. Disconnect the motor harness from the MCU. With an ohmmeter, verify the resistance values as shown below:
Motor Harness Winding
Pin 1 & 3 8.5 - 14.0 ohms
Pin 2 & 3 8.5 - 14.0 ohms
Pin 1 & 2 8.5 - 14.0 ohms
If the values are outside the range or open, replace stator assembly; otherwise, reconnect the motor harness and go to step 8.
8. Check the two harnesses between the CCU and MCU for continuity. If there is continuity, go to step 9. If there is no continuity, replace the main lower harness.
9. With a voltmeter set to AC, connect the leads across pins 1 and 2 of connector MS2.
10. Plug in washer or reconnect power.
F2 code has been coming up for awhile. Techs come in clean filters. I clean them often. Their not clogged or blocked-drum doesn't spin. I start wash cycle, it doesn't finish but gives f2 code. I change cycle to rinse and drain and speed of spin from high to medium and works once then next wash cycle I do same but have to try slow spin. Husband already placed new drain pump. He s wondering if he should try one of control panel. Which or what do you think is wrong. Thank you for your help
With the issue that you are having with the F2 error code you will want to check the pressure hose to ensure that it is not clogged. Also check the connectors at the control board and at the drain pump for corrosion and if there is any corrosion then you would want to clean with a contact cleaner. Also check the hose that comes from the bottom of the tub to the drain pump for any debris that may be in it. Clear any out if found. If all this checks ok then the main control board 8182695 would be the most likely issue.
Hello, I have been looking at the other feeds. I have an F6 code error. When I ran the diagnostic check the motor never spun. I looked at the connectors and plugged/unplugged. Just put a new motor in and same code. From what I am reading, it sounds like the MCU, your thoughst? Thanks for your time,
Answer Hello Dave. Per the manufacturer • Check wire harness connections between the Drive Motor/Tachometer and the Motor ControlUnit (MCU), and between the MCU and the Central Control Unit (CCU)
• Check the Drive Motor
• Check the MCU
• Check the Wire Harness
If harness is good then the mcu will probably be the issue.