24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Customer Questions and Answers for Pcb (mems) Sensor by Whirlpool

  1. Our Price $79.79
    Compare At $94.95
    You Save $15.16
     
    • Part Number: AP4044365
    • MFG Part Number: 34001484
    • Made by: Whirlpool
    Add to Cart

Questions & Answers

For Whirlpool Pcb (mems) Sensor (Part Number: AP4044365)

Ask a Question

Most Interesting  |  Latest Questions

The problum I am having is the pump starts and stops and trys again to start and stops, then go's in to nd code after while. I checked the voltage going to the pump, it is fluctuating. Is there another control for the pump? Everything else seems to operate just fine.

Art for Model Number NFW7200TW

Answer

Was this helpful?

1 Answer

After the water was fill up and drum was rotated 4 times the washer stop working and display show me error cod E3. Please help me.Thanks.

Simon for Model Number mah8700aww

Answer

Was this helpful?

1 Answer

My Maytag Neptune does not drain. Pulled of back and disconected hoses and checked pump and had no resrictions. During wash cycle it stops at spin and gives ND code but when this comes up and I shut power off and let set for a couple of minutes then choose "Spin Only" the washer will run thru cyle and spin cloths dry. I belive I need a control board the serial number of washer is (S)12535302GT. Can you help me out, I dont wont to order a board from you until I ask first. Thanks

Blaine for Model Number mah8700aww

Answer

Was this helpful?

1 Answer

I did the check for motor failure and the OHMS on all points was 11.3, you say it's supposed to read 11.6, Does this mean my motor is bad?

Gw for Model Number MAH9700AWW

Answer

Was this helpful?

1 Answer

On the spin cycle is shows the error code 3E but it does not do it every time. It does it maybe 3 out of 5 times, can you help me with this?

Gw for Model Number MAH9700AWWMAYTAG

Answer

Was this helpful?

1 Answer

I keep getting error code E3 what does this mean

Gw

Answer

Was this helpful?

1 Answer

I'm getting a E2 error on the display and washer will not operate at all. the machine stopped with the basket full of water. What does this code mean?

Chuck for Model Number nfw7200tw

Answer

Was this helpful?

1 Answer

my washing machine goes through the wash cycle, and stops at rinse and spin the pump does not kick on for it to drain. I have taken the pump off and wired it direct and it works fine, i also checked all lines and tub for blockage. I also check the voltage in the wire coming in pump from control board and it is 118 V. I but machine doesn't drain and error comes is "nd". is it pump/control board or reactor?

Danish H for Model Number IFW7200TW

Answer

Was this helpful?

1 Answer

Everything in the machine is fine until it has to drain. Then we have to pump the water out and the washer works fine. And then it moves on to the next cycle. We checked the pump and its working but the output from the control board is 120 v but the pump only gets 20 v. What could be the problem? could it be the MEMS sensor or door switch?

Witold for Model Number mah6700aww S#15077558le

Answer

Was this helpful?

1 Answer

my washing machine goes through the wash cycle, rinse and spin but the pump does not kick on for it to drain. I have taken the pump off and wired it direct and it works fine, i aslo checked all lines and tub for blockage. Do you think the problem is in the control board? thank you for your time and help, Gary

Gary for Model Number nfw7200tw

Answer

Was this helpful?

1 Answer

 

 
 
We are Safe, Secure, Dependable and Trusted
  • BizRate.com Customer Certified Site - Click to Verify