Oven will not spark or click when turn on . Broiler works fine.
Woody for Model Number wfg361lvt-1
Answer Hello Woody. If there is no power from the control board when bake is selected, you will need to replace the board W10424331. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html
It won't light up in oven just coil gets red.
Caifan for Model Number kgra806pss01
Answer Hello Cailfan. Test the gas valve. Component Check
Check between each
solenoid for 216 O
resistance (Broil terminal
to Common, and Bake
terminal to Common).
NOTE: Always check
both solenoids. If one of
the solenoids is defective,
neither one will operate. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html
Oven/Broiler ignition clicks twice but does not ignite. All controls - temperature, timer, oven "on" indicators appear to be working but the oven or when in broiler mode is not operating. Likely problem the spark module or if unit has one the oven spark igniter?
Chuck C for Model Number SF368LEPS2
Answer Hello Chuck,
The first thing to check is the is to make sure that you are getting proper voltage to the direct spark ignition control. With oven on broil you want to have 120vac between connectors J1-4 neutral and J1-7 L1. If you don't have power here then you need to replaced Clock assembly 6610449 black, 6610450 white, 6610451 biscuit. If you have power the test from J1-4 to J1--2. If you do not have power then replace spark module W10331686. If you do have power then replace spark ignitor 8054129. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html
Good Afternoon. The stovetop is working, but the oven and broiler isn't working. When you press the igniter button for the oven you smell gas, but it doesn't lite. When you try to start the broiler nothing happens and no gas smell. Any suggestions will be helpful.
Gary B for Model Number Whirlpool SF265LXTS2
Answer Gary, Your issue is most likely in the DSI Spark Module W10331686, but could be in the gas distribution valve W10293048 Here's some test information, that will help you out. First thing, check and make sure the power cord is attached to a properly polarized and grounded 120 VAC outlet. A proper ground is very important for the range to operate properly. Then you'll need to make several tests at the gas distribution valve. You'll need a multi meter to test voltage and resistances. At the valve body terminals, with the wires labeled and removed from the middle terminal to each of the outer terminals, you should read 215 ohms resistance. With the wires reconnected, when you select the bake cycle, you should have a reading of 8 to 18 VDC across the red and orange wires. When you make a broil selection you should have the same 8 to 18 VDC,across the orange and blue wires. If all checks are proper(within 10%) repalce the gas valve and check the wiring at the igniters. Thanks
Sometimes my oven won't light and other times it fires right up. When it doesn't light it will click like it's trying to and keep clicking then stop. I have to keep turning the oven off waiting a few minutes and try again. Sometimes it can take hours till the oven will finally light sometimes it will only take a few tries. I was thinking maybe it was the igniter??
Kristy for Model Number 66575012101
Answer Kristy, The issue is most likely in the reignition circuit of the DSI spark module W10331686 . There are circuit checks and VDC checks you should make at the gas distribution valve, with a multimeter, with the wires off the valve terminals, you should have a resistance reading of 215 ohms from the middle terminal to each outer terminal, and 8 to 18 VDC from the center terminal (orange wire) to the outer terminal(redwire)with the oven set in a bake cycle and the igniter attempting to ignite. heres some meter usage information [http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html] Thanks and Good Luck
Oven works but broiler does not spark and no gas smell. Replace inginter already
Bob for Model Number whirlpool gas oven sf362lxts 0
Answer Hello Bob. If the igniter is new and the wires are good, you will need to replace the spark module W10331686. Hope this helps.
Oven igniter sparks, and you can smell gas but oven does not turn on. Unit had worked fine until yesterday. It is about 7 years old with almost daily use. What could be the issue?
Guest for Model Number Whirlpool sf379lekq gas range
Answer Hello. Are you sure the bake ignitor is sparking? If the ignitor 8190618 is not drawing enought amps to satisfy the gas valve, gas will not flow to ignite. You could have a issue with the gas valve/regulator W10293048. Hope this helps!