24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Customer Questions and Answers for Door Switch by Whirlpool

  1. Our Price $15.33
    Compare At $21.59
    You Save $6.26
     Watch Video
    • Part Number: AP3039128
    • MFG Part Number: 8269209
    • Made by: Whirlpool
    Add to Cart

Questions & Answers

For Whirlpool Door Switch (Part Number: AP3039128)

Ask a Question

Most Interesting  |  Latest Questions

As recommended got a new door switch and replaced the old with new one but it did not solve my problem.Still see two dashes without any other action.Need further help pl. Seth

Seth for Model Number GU2400XTPS6

Answer

Was this helpful?

1 Answer

I have had my whirlpool - Quiet Partner 3 for 1 year and 4 months( off warranty of course). I also had power outage for 3 hours. The dishwasher would never come back on. I tested main volt coming in. No issues it's 120. I'm trying to sort out the next step. No lights and no power. I have read several reviews to check. One I'm concerned about is the door latch switch, the one on the right tested 120v. The switch on the left was .1 no reading. should that part number 8269209 have the same 120 v current on the test? Do you think this is this issue? thanks

Melissa for Model Number gu2300xtvb1

Answer

Was this helpful?

1 Answer

i put new front panel on dish washer and it work great for about 5 times then it quit again they sent me a new panel this one does the same . I have current to the main switch but i think thats a far as it goes. no juice to door switch, should i just buy a new one? thanks rich

Rich for Model Number 66516462300

Answer

Was this helpful?

1 Answer

I bought the dishwasher from a friend who had never used it, in fact it would not run. I found that there was no spring to pull down the T shaped actuator for the two door switches. Can you tell me the part number of the parts I need to buy to make the switches operate.

Gerry for Model Number GU1200XTLO2

Answer

Was this helpful?

1 Answer

Hello, my dishwasher will not start. I have verified it is getting power, first indication was that the Air Dry, Sani Rinse, and Hi Temp Scrub buttons would light up when pressed. None of the Wash options (Pots and Pans, Normal wash, etc) will light up when pressed. I found the reset procedure online, and pressed the Air Dry and Hi Temp Scrub buttons back and forth 5x. At this point all the lights on the control panel lit up, and it went into the 2 minute diagnostic cycle as expected. When that completed, it was still the same as before, it would not start when I press the Start button. Any ideas?

Nathan for Model Number 665.16919

Answer

Was this helpful?

1 Answer

Thanks for your answer over on the console assembly page. You recommended look at the switch, I took it off and the metal was in pieces. I touch the wires together and the machine starts! I will order a new switch, question is, how does it work? I don't see how anything would open the switch, its not attached to the moving part of the latch handle, only the plastic posts on the latch assembly. I am worried that I will not put the new one on correctly, so some knowledge would do me some good. Thanks.

Dave for Model Number KUDM01TJ

Answer

Was this helpful?

1 Answer

We had a power outage for four days, we tried to use the dish washer after service was restored and it would not work. We pressed the normal wash and the steam and heated dry lights come on but when we push start they go off after about 30 sec. and nothing happens? Thanks Larry

Larry for Model Number MD87709AWS2

Answer

Was this helpful?

1 Answer

My dishwasher would go through 2 cycles in normal mode then I would get a clean light flashes 7 times continuously. I just installed a new heater and a new hi-limit thermostat and reset the panel. The same thing happens. 2 cycles then the clean light flashes 7 times. What else could it be that causes the clean light to flash? Thanks

Ghost for Model Number kudso1flss6

Answer

Was this helpful?

1 Answer

Thank you for responding to my original question (machine's buttons light, but the machine will not start-the unit will discharge water), the machine's float mechanism is working properly, but it is still not working. What would be the next step please. Does the fact that it will discharge water rule out door switches and the control panel?

Robert for Model Number kudpo1flss6

Answer

Was this helpful?

1 Answer

My machine does not start. The button lights go on but nothing happens. If I put water in the unit, and hit the cancel button and close the door, the water will drain.

Robert for Model Number kudpo1flss6

Answer

Was this helpful?

1 Answer

 

 
 
We are Safe, Secure, Dependable and Trusted
  • BizRate.com Customer Certified Site - Click to Verify