24/7 Customer Support

CHECKOUT
Items in Cart:
Total
$0.00

Customer Questions and Answers for Switch-Wl by Whirlpool

  1. Our Price $48.10
    Compare At $59.48
    You Save $11.38
     Watch Video
    • Part Number: AP5669582
    • MFG Part Number: W10514214
    • Made by: Whirlpool
    Add to Cart

Questions & Answers

For Whirlpool Switch-Wl (Part Number: AP5669582)

Ask a Question

Most Interesting  |  Latest Questions

Note: This question is for the older version of this part, but we thought you might still find it helpful

For checking the pins 21 and 22,are they labeled as such? Also is the part for the whirlpool duet the same as for the Epic? We have FH code, replaced flowmeter, now may try the pressure switch, but would like to do the test. When you say open or closed, will we know right away just by looking? Is there a detailed picture of the pins we need to check? THANK YOU!!!

Kim B for Model Number MFW9800TKO maytag epic

Answer

1 person found this answer helpful.

Was this helpful?

1 Answer

Note: This question is for the older version of this part, but we thought you might still find it helpful

How do I test the water level switch to see if it's any good?

Pas for Model Number GHW9100LW2

Answer

1 person found this answer helpful.

Was this helpful?

1 Answer

Note: This question is for the older version of this part, but we thought you might still find it helpful

How do I install the water level presure switch? It did not come with installation instructions.

Mark for Model Number ghw9150pw0

Answer

1 person found this answer helpful.

Was this helpful?

1 Answer

I replaced both parts W10514214 & W10110225 and did a little better. Ran through the add soap cycle and four other short water burst. Then as it added the water for the wash cycle it keep adding water until it hit the h f trouble code and pumped the water from the tub.

Kenneth

Answer

Was this helpful?

1 Answer

My Kenmore 11045089400 is stopping at the end of the wash cycle and flashing an FH trouble code. Pump is new and draining, filter and hoses are clear, what is the most likely problem? Pressure switch or flow valve? Can't run a diagnostic code because the tech sheet is gone too! Help?

Darrell for Model Number 11045089400

Answer

Was this helpful?

1 Answer

I have the same problem as Dan. I replaced the presume switch but tub still fills until it triggers the f/h code. It then empties the water from the tub. I did find a nick in the ribbon wire harness. I found that the custom and rinse and spin no long will light, Or operate. Could this be a reason for the water to fill until it triggers the trouble code?

Ken for Model Number 45872400

Answer

Was this helpful?

1 Answer

My duet front load ht washer is not filling up. It turns on but no water. It stays in drain mode but there is no water in it, I hear the motor trying to suck water.After awhile it starts flashing F09. Now I've read F09 is a overflow code, but I also read somewhere else the pressure switch could be bad and it would cause that symptom I am having. One more thing, from pressing pause/cancel then control/on then start it actually started going into the wash mode like there was water in it, but it was bone dry. Any thoughts? Do you think this part is a start?

Jordon for Model Number GHW9400PT1

Answer

Was this helpful?

1 Answer

How to test?

Mike for Model Number GHW9150PW0

Answer

Was this helpful?

1 Answer

My water won't stop entering the tub. I have replaced the water inlet valve 8181694 and the switch AP5669582 MFG Part Number: W10514214 Made by: Whirlpool the water still does turn off

Dan for Model Number GHW9150PWO

Answer

Was this helpful?

1 Answer

I just moved into a house that has a Whirlpool HT Duet front load washer, when the water loads in it fills up starts leaking. Oddly enough when I looked at the drain it is draining properly. I took off the back and saw that the leak is coming from where the pressure tube connector connects to the (i dont know what its called but barrel where the clothes are washed) It comes out pretty consistantly. I unplugged it and a ton of water came out, I checked the tube and connector and there wasnt any clogging going on. What do you think it is? The pressure switch? do you think the fitting was in there loose? Or could there be another reason.

Tyler R for Model Number Whirlpool HT Duet Front Load Washer

Answer

Was this helpful?

1 Answer

 

 
 
We are Safe, Secure, Dependable and Trusted
  • BizRate.com Customer Certified Site - Click to Verify