Could the thermal fuse be the issue if the oven and control panel lighting are not functioning? The range top is functioning normally at all four switches and burners.
Answer Hello Johnny,
The thermal fuse is only in line with the broil element. This issue will most likely be the clock assembly 9757271. Since this board has been discontinued with no satisfactory substitution listed by the manufacturer, your best bet would be to contact corecentricsolutions.com to see if they support this board for remanufacturing. You would have to send the board to them for the repair so you would definitely need to take several pictures from several directions so you will be able to reconnect the wiring when it gets back. This avoids a lot of frustration and possible mis-wiring that could cause damage to the clock assembly or other components.
Power to oven works fine. Everything works except elements, bake and broil. Will power still work on oven if thermal fuse is blown?
Answer Hello Eddie. Yes, it still works, but the elements will not heat. The thermal fuse should read closed for continuity. If it is good, replace the control board on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html
Hi, when the oven is set to bake at 350 the temperature will swing from 327 to 417 or more. There doesn't seem to be any temp consistency at any pre-set temp. Is this the temp sensor or control board?
You will want to check the temp sensor for resistance. At room temperature the sensor should be 1090 ohms. If outside of 10% of this then the sensor is bad and would need to be replaced. If this checks ok then the oven control board is faulty and would need to be replaced.
oven will not heat up. i replaced oven sencor and still dont work. the heating element is not geting any power to it.
Answer Larry, the thermal fuse is a good place to start, if it is "open" it will interrupt power to the broil element, and create a low temperature issue in the oven. At the oven control / ERC you may need to test voltage out to the elements Con. 2in 7 red wire to chassis ground should read 120 VAC in a bake mode. Con2 pin I blue wire should have 120 VAC to chassis ground in the broil mode. Both red wires on con 4 should read 120 VAC to chassis ground. Be careful with the voltage checks, don't hurt or shock yourself. if all the voltages are present and correct the ERC is not the issue and the thermal fuse and wiring will need to be checked and replaced or repaired.
My broiler element does not work. I get no heat but element is good. The bake works fine but the top oven burner does not work.
You will want to check the oven selector switch between black and brown with the oven set for broil for 240 vac if there is 240 vac then the oven switch is bad and will need to be replaced. If there is not 240 vac then check for continuity on the thermal fuse and replace if there is no continuity.
Is this thermal fuse what I need if the buzzer on my timer dosen't work or any button I press doesn't make a sound
The buzzer for the timer and the chime on the touchpad is controlled by the electronic control board not the thermal fuse. The thermal fuse would cause the electronic control to not be lit.
I turned the stove on for the first time since it had been sitting for 6 months.. I set it to 225 degrees.. it cut on and within 10 mins the entire thing shut down and has no power. Nothing on the control panel and the Magnitogorsk don't work. Would this be the thermal fuse that needs replacing?
Answer Hello Brittany,
Yes it is very possible that the thermal fuse is faulty. Also check the terminal block to make sure that you are getting 120 vac across L1 to ground and L2 to ground and 240 vac across L1 to L2. Check the thermal fuse for continuity if no continuity then replace the thermal fuse.
Broiler will not shut Off, only way is shut of the broiler is by the fuse panel. I recently replaced the oven temp. sensor.
Answer Hello Dennis,
The broil element runs through the control board. If it is sending constant power to the element then you would need to replace the control. Also check for broken wires that may short to ground to create a circuit. If broken wire found would need to be repaired.