washer will spin and drain will not agitate.Pulled the transmission cover and its fine. Do you sell the oil for the transmission or can you use automotive type gear oil? I am guessing the timer is bad how do I do a pinpoint test on it? Or just order the timer and send it back if that doesn't fix it? the washer is 21 years old so I am not going to invest a whole lot of $$$ in it.
Answer Jeff, The part number for the gear oil is 6-0560800 Based on your post, the issue would be in the timer 22001025, if the motor operates in one direction, it's 99%, the motor is not the issue. Basically To pin point the issue in the timer you'd unplug the power cord, set the timer dial to a wash cycle, pull out the knob and disconnect the multi plug connector. Then you'd check for closed circuits between the contacts on the timer based on the wiring diagram and timer cam or cycle chart. But first, have you checked the lid switches and fuse. Yes, if the timer does not solve the issue, you can return the part for a refund, but you'll be responsible for the return shipping. Thanks
Is it difficult to replace the timer?
Answer Hello David,
It is not hard to replace the timer at all. Unplug the washer and take the screws out from across the top of the control panel. Remove the knob by popping the center out and remove the little "c" clip. Be careful not to lose it! Pull the outer part of the knob off and remove the two screws securing it to the panel. With the timer loose, you can depress the retaining clips on either side of the harness connector. Once you have removed both of the connectors, reverse the procedure to install the new timer. Reestablish the electrical connection, (plug it back in), and try the unit to insure the connections made and your done.
When my rinse cycle comes on, the water runs into the tub and and keeps draining out, and the water runs forever. If I do not turn it off. When I turn the timer back to the rinse cycle it sometimes works right.
Answer Hello Cindy. You will need to check and make sure there is an air gap for the drain hose to breath in the unit, and that the drain hose is not to far into the drain pipe and is siphoning out. It sounds like that is the issue with the information you provided.
You set how much water you want, and then the washer fills more than you want....is that a timer problem???
Answer Hello Richard. No, based on the information you provided, it sounds like the pressure switch 208202 or the pressure switch hose is bad and will need to be replaced. Check and see if the hose is torn or has a hole in it. If so, replace the hose. If not, it may just be the pressure switch. Hope this helps.
How do I remove the timer from the panel ? There are no visible screws...........
Answer Hi Michael. Remove the power. According to the timer noted part # 22001025, this is used on Lat8.... models. Since we do not have the exact model # it can be removed by Unscrewing the timer knob. The knob skirt is spring loaded so be careful not to loose the spring. then you can access the front screws that mount the timer. Remove the back and replace the timer. Re mount the new one and reassemble the unit. Thank You.
My washer fills up with water but then it will not wash or spin could this be the problem ??
Answer Hi Gloria. You will need to replace the lid switch assembly. Make sure that before you remove the old one you mark the switch base against the top panel itself so the new one will align with the marks. You will need to lift the lid and replace the switch assy. part # 22001682. Thank you.
My 17 yr old maytag #lat8214aae clothes washer timer rotates during a cycle, but at times the cycles do not occur. Is this indicative of a bad timer? Specifically, how does one troubleshoot this device? The AP4028326 timer is ~$120.
Answer Hi Dave. If You are familar with the use of an ohm meter, you can isolate the timer and diagnose. By following the timer chart, you can advance th timer to see if the contacts close at the correct times. This will be the part to replace if you have intermittent cycles as described. This timer is part # 22001025. Thank you.