Questions and Answers for Whirlpool W10253864 Tub-Outer

Answer Hello Jman, Unfortunately to replace the bearings on the tub of your unit you will have to replace the outer tub W10253864. The manufacturer does not have a bearing kit for this unit. Because the bearings are pressed in the outer tub would have to be replaced.

Was this helpful?

Yes

1 Answer

Note: This question is for the older version of this part, but we thought you might still find it helpful

For the Rear outer tub, 285984, did Whirlpool change the bearing size? I just got a new one and it is bigger than the shaft.

BEEF38 for Model Number GHW9100LQ1

Answer Hello Beef38! The outer tub W10253864 is a manufacturer replacement part and may differ in appearance but is a functional equivalent to the original and will work on your model GHW9100LQ1. Thanks!

Was this helpful?

Yes

1 Answer

Note: This question is for the older version of this part, but we thought you might still find it helpful

1 repair tech diagnosed the cause of knock on high speed spin as a bad shock & another said the spider on the inner tub was bad. I don't feel any play on the pulley at the back of the outer tub. The shocks seem a little sloppy but seem all the same. How can I determine the cause of the knock?

Hankr for Model Number WFW8410SW01

Answer Hello Hankr. Pull the unit out and remove the back access panel on the unit. Then, turn the unit on and let it run. Check and see if the noise is coming from the pulley or the shocks. You should be able to determine this being behind the unit with that cover off the unit. Then you can determine if it is the bearings and spider assembly or the shocks.

Was this helpful?

Yes

1 Answer

Note: This question is for the older version of this part, but we thought you might still find it helpful

This unit was bought in October of 2003 (9 years ago). The outer tub has failed so both tubs will need replacing. The warranty says 2 through 10 years, the outer tub is covered. How does the do-it-yourselfer get free parts without involving a costly serviceman?

El M. for Model Number GHW9100LW1

Answer Hello, The parts have to be provided through an authorized factory servicer and will not be covered under any warranty unless installed by such.

Was this helpful?

Yes

1 Answer

Note: This question is for the older version of this part, but we thought you might still find it helpful

I have the heavy banging sound on spin cycle along with the popular plastic scraps shedding in my wash as mentioned here already. But I also have a bad leak occurring at the front of the washer and a squeal coming from the inside rear when it transitions to rinse. Do I replace the whole tub assy and if so could you assist me in the correct parts I will need to complete this job? I realize parts of this issue has already been addressed but I would like to be sure. Additional recommendations will be of great value!! Thank You.

IGOTTOOLS2 for Model Number GHW9150PW0

Answer Hello Igottools2. Based on the information you provided, you will need to replace rear tub W10253864 and the front tub assembly 285982. Hope this helps.

Was this helpful?

Yes

1 Answer

Note: This question is for the older version of this part, but we thought you might still find it helpful

I have a 2005 whirlpool Duet that has a banging noise on high speed spin towards the end of the cycle. I have repalced the shocks and the noise is still there. I cleaned out the pump strainer and found some small 3/16 x 1" pieces of black plastic. There is some out of roundness when you rotate the drum and some movement if you lift the inner drum from the outside. There is no water leaking. Is the tub bearing bad?

Waterman for Model Number GHW9150PW

Answer Waterman, Very Good deduction, Yes, you would most likely have a worn out tub bearing or even a damaged/defective trunion arm on the spin basket shaft (rare but possible) . You'd need to replace the rear outer tub and bearing assembly, if that's the case W10253864 Thanks and Good Luck

Was this helpful?

Yes

1 Answer

Note: This question is for the older version of this part, but we thought you might still find it helpful

Is the seal available? I have found and replaced the bearings, but would have liked to replace the seal, because I beleive this took out the bearings.

Woody for Model Number 110.42822203

Answer Hello Woody. No, you will need to order the tub assembly W10253864 for the seal. Hope this helps.

Was this helpful?

Yes

1 Answer

Customer Questions and Answers for Tub-Outer by Whirlpool

Tub-Outer

Questions & Answers

Most Interesting | Latest Questions